background image

 

Table 2. List of control parameters and its initial settings 

 

Warranty 

Auber Instruments warrants this controller to be free from defects in material and 
workmanship for a period of one (1) year from the date of the original purchase when 
utilized for normal household use, subject to the following conditions, exclusions and 
exceptions. The sensor of the controller is warranted for 90 days. 
 
If your appliance fails to operate properly while in use under normal household 
conditions within the warranty period, return the complete appliance and accessories to 
Auber Instruments 
730 Culworth Manor 
Alpharetta, GA 30022. 
If the appliance is found by Auber Instruments to be defective in material or workmanship, 
Auber Instruments will repair or replace it free of charge. A dated proof of purchase may 
be required. 
 
The liability of Auber Instruments is limited solely to the cost of the repair or replacement 
of the unit at our discretion. This warranty does not cover normal wear of parts and does 
not apply to any unit that has been tampered with or used for commercial purposes. This 
limited warranty does not cover damage caused by misuse, abuse, negligent handling or 
damage due to faulty packaging or mishandling in transit. This warranty does not cover 
damage or defects caused by or resulting from damages from shipping or repairs, 
service or alterations to the product or any of its parts which have been performed by a 
repairperson or facility not authorized by Auber Instruments.   
 
This warranty is available to the original purchaser of the unit and excludes all other legal 
and/or conventional warranties. The responsibility of Auber Instruments, if any, is limited 
to the specific obligations expressly assumed by it under the terms of the limited warranty. 
In no event is Auber Instruments liable for incidental or consequential damages of any 
nature whatsoever. Some states/provinces do not permit the exclusion or limitation of 
incidental or consequential damages and therefore the above may not apply to you. 
 
This warranty gives you specific legal rights and you may also have other rights which 
vary from state to state or province to province. 
 
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of 
purchase date and to attach tag to item before packing with your name, complete 
address and phone number with a note giving purchase information, model number and 

 
 

14

 

 
 

Содержание WS-1500APH






















Отзывы: