ATWELL UMD-SRB01 Скачать руководство пользователя страница 28

27

UMD-SRB01 

Version 4

Definitions

For the scope of this documentation the following terms are clarified to 
have the described meanings.

Owner of the Lift

The natural or legal person who has the power of disposal of the lift and takes 
the responsibility for its intended operation and use.

Emergency

 

An abnormal situation in which persons require outside assistance.

Fault

A situation of operation in which safe operation of the lift for its intended use is 
restricted or impossible.

Installer

The natural or legal person who takes responsibility for the design, manufacture, 
installation and handover of the lift, including its safety components.

Maintenance Company

A company which is given responsibility for carrying out company maintenance 
operations, and which has competent persons at its disposal.

Maintenance Operations

All necessary operations (lubrication, inspections, cleaning, operations etc.) to 
ensure the correct and safe functioning of the lift after the completion of the 
installation.

Repair

Replacement or repair of defective and/or worn components.

Safety Components

Components which are defined as safety components in the EU Lifts Directive 
(2014/33/EU).

Competent Maintenance Person

Persons with the knowledge, technical ability and equipment able to perform  
the tasks allocated to them without danger.

Содержание UMD-SRB01
































Отзывы: