background image

SAFETY PRECAUTIONS

SPECIFICATIONS

2

C1 Electric Catamaran

Length: 53.5in/1360mm
Overall Length: 58in/1470mm
Beam: 15in/380mm
Height: 9in/230mm
Overall Height: 13in/330mm
Weight: 13lbs (with battery)
Recommended Battery: 22.2V 25C 
5000mAh LiPO
Run Time: 8-10 minutes 
(22.2V 5000mAh LiPO)

Radio Equipment

Transmitter: Atomik 3Ch 2.4Ghz
Dimensions: 230 x 175 x 75mm 
Weight: 1.4 lbs/566 oz (with battery) 
Receiver: 8188 4-Channel Micro Receiver
Servo: 1825 High Torque Metal Gear
Speed: .17sec/60º
Torque: 107 oz/in (7.0kg.cm) @ 6V

Note! Product specifications are subject to change.

• Never swim out to retrieve an R/C boat that has stalled in the water. If you are going into the water, use 

  a small boat or kayak to retrieve your model.  Always wear a PFD (Personal Flotation Device).
• Never stand in the water when operating your model boat.

• Remain clear of the propellers when the boat is running. Pay extra close attention to loose clothing,  

  jewelry, long hair and anything that can be caught in the spinning prop. 

CAUTION: A spinning 

  propeller can cause severe injury.

• 

The propeller and other running hardware are very sharp. Use extreme caution when working on or 

  around these parts. 

• Your model is operated by radio signals sent by the transmitter. This system is susceptible to interference

  from other radio signal sources. Before using your model, make sure that there is no other interference in the area. 

• Never operate your model near swimmers or wildlife. The size and speed of this model can cause severe 

  injury and damage if a collision occurs.

• Some of the electronic components may become very hot during use and can severely burn you if 

  touched before they cool. Let the model stand and cool down before handling the motor, ESC and cooling 

  components.

• The battery used in this model can be dangerous. If the battery gets hot during charging, discontinue charging 

  immediately and disconnect battery from charger. Never leave the battery unattended while charging. If you are 

  unsure of how to charge this battery, please contact Atomik™ or seek the advice of your local hobby shop. 

  Never let children charge batteries without adult supervision.

• Charging and discharging batteries has the potential for serious injury to persons and damage to property. In 

  purchasing this product, the user agrees to accept responsibility for all such risks, and will not hold Atomik™, it’s 

  affiliates, manufacturers, distributors, or retail partners responsible for any accident, injury to persons, or 

  damage to property resulting from the use of this product. 

• This product contains chemicals known to the State of California to cause cancer, birth defects and other     
  reproductive harm. Be responsible, dispose of properly.

• Always check your model for loose screws and components before operating. 

• Always stop the engine before removing debris that has become tangled in the prop.

• Minors under the age of 18 require adult supervision when using this boat.

Atomik™ 120A Pro Marine 
Brushless Speed Control

Continuous Current: 120A
Burst Current (10S): 240A 
BEC Mode: Switch
BEC Output: 6V/3A
Battery Cells:
LiPO: 2-6
NiMH: 6-18
Weight: 93g 
Water-cooling Pipe Dia: 5mm
Dimensions: 94 x 33 x 18mm

V700 1100Kv Outrunner Marine Motor

Weight: 12.2oz (346g)
Dimensions: 48 x 58mm
Shaft Diameter: 5mm
Input Voltage: 2-6S LiPO
MAX RPM: 40K
MAX AMP: 130A
Resistance (I/O):0.0416

Содержание A.R.C. C1





















Отзывы: