ATN PVS7-HPT Скачать руководство пользователя страница 59

Страница: 59 / 64

3-7

Figure 3-1. Re-installing the Neck Pad

3. Repeat steps 1 and 2 for the other side of the headband and neck

pad if necessary.

C. Lacing the Sliding Bar Buckles.

While donning and adjust-

ing the head mount, it is possible for a strap to slip out of a slide

fastener. Perform the following procedure to replace the strap and

sliding bar buckle.
1. Thread the strap from the inside of the buckle over the move-

able sliding bar (see Figure 3-2). Thread the strap back through the

buckle but this time under the sliding bar and over the serrated part

of the buckle.
2. Pull the strap through the buckle and tighten as necessary.
3. Repeat steps 1 and 2 for any other straps and buckles that may

have come undone.

Figure 3-2. Lacing the Sliding Bar Buckles

Lower Strap

Retention Tab

Lower Strap

Retention Tab

Lower Strap

Retention Tab

Fixed

Serrated Bar

Moveable

Sliding Bar

Содержание PVS7-HPT

































































Результаты поиска

Содержание PVS7-HPT

Отзывы:

Бренды по названию

Популярные бренды

ATN PVS7-HPT, Руководство пользователя

Результаты поиска

Содержание PVS7-HPT

Отзывы:

Бренды по названию

Популярные бренды