ATN PVS7-HPT страница 26 Скачать руководство пользователя

Страница: 26 / 64

2-4

ITEMS

CONTROLS AND

INDICATORS

FUNCTIONS

Objective Focus

Focuses objective lens. Adjusts for

sharpest image of viewed object.

Battery Polarity In-

dicator

The feature, molded into the PVS-

7, shows the proper orientation of

the batteries.

Latch

Latch used for separation of gog-

gle assembly from head mount/

helmet mount assembly.

LED On Indicator

(Not Shown)

When illuminated (left eyepiece)

it indicates that the IR illumination

is on.

Low Battery Indica-

tor (Not Shown)

When illuminated (right eyepiece)

it indicates a low battery condition

with less than 30 minutes of bat-

tery life remaining.

Diopter Adjustment

Ring

Focuses eyepiece lens for each

eye without the need for glasses.

Adjusts for sharper image of inten-

sifier screen.

Interpupillary Ad-

justment

Adjusts for distance between

eyes by sliding the eyepieces ei-

ther together or apart so each eye

can observe the entire field at the

same time

Eye Relief

Adjusts the distance between your

eyes and the goggle.

Содержание PVS7-HPT

































































Результаты поиска

Содержание PVS7-HPT

Отзывы:

Похожие инструкции для PVS7-HPT

Бренды по названию

Популярные бренды

ATN PVS7-HPT, Руководство пользователя

Результаты поиска

Содержание PVS7-HPT

Отзывы:

Похожие инструкции для PVS7-HPT

Бренды по названию

Популярные бренды