background image

3-3

MALFUNCTION

TEST / INSPECTION

CORRECTIVE  ACTION

4. Light visible 

around eyecup

Check eye relief dis-

tance

Check  eyecup  for 

resiliency

Readjust for proper eye 

relief distance

If eyecups defective, re-

fer to higher level of main-

tenance

5. Diopter ad-

justment  can-

not be made

Check to see if the 

diopter adjustment 

ring is bent or bro-

ken

If damaged, refer to high-

er level of maintenance

6.  Interpupil-

l a r y   a d j u s t -

m e nt  c a n n ot 

be made (left & 

right eye)

Defective eyepiece 

assembly

Refer to higher level of 

maintenance

7. Battery cap 

difficult to turn

Check for dirt or grit 

in threads

Visually inspect for 

the presence of an 

o-ring

C h e c k   f o r   d a m -

aged battery cap or 

threads on battery 

compartment

Clean

If o-ring is missing: refer 

to higher level of mainte-

nance

If damaged, refer to high-

er level of maintenance

8. PVS-7 does 

n o t   s h u t   o f f 

when removed 

f r o m   h e a d 

mount  during 

operation

Visual

Return  both  the  PVS-7 

and  head mount to higher 

level of maintenance

Содержание PVS7-HPT

































































Отзывы: