Atmel SpaceWire Router SpW-10X Скачать руководство пользователя страница 39

Страница: 39 / 155

Ref.:

UoD_SpW-10X_

UserManual

Issue:

3.4

SpW-10X

SpaceWire Router

User Manual

Date:

July 2008

Preliminary

146
145
144
143

EXT10_IN_DATA(3)

EXT10_IN_DATA(2)

EXT10_IN_DATA(1)

EXT10_IN_DATA(0)

(0)(dddddddd)

- Data byte

(1)(XXXXXXX0)

- EOP.

(1)(XXXXXXX1)

- EEP.

Bit 7 is the most significant bit of the data byte.
Pull-up resistors (e.g. 4k7

) should be

connected to these inputs if External FIFO port
10 is not being used.

152

EXT10_IN_FULL_N

Out FIFO ready signal for external input port one.

When high there is space in the FIFO so it can
be written to. When low the FIFO is full.

CMOS3V3

153

EXT10_IN_WRITE_N

Asserted (low) to write to the external input
port one FIFO.
A pull-up resistor (e.g. 4k7

) should be

connected to this input if External FIFO port 10
is not being used.

CMOS3V3

See section 6.1 for information on the operation of the external ports and section 10.3 for timing
details.

5.4 TIME-CODE SIGNALS

The time-code interface signals are listed in Table 5-4. The timing of this interface is shown in

Figure 6-3 and Figure 6-4.

Table 5-4 Time-Code Signals

PinNo Signal Dir

Description

Type

158

EXT_TICK_IN

The rising edge of the

EXT_TICK_IN

signal is used

to indicate when a time-code is to be sent. On the
rising edge of the

EXT_TICK_IN

signal the

SEL_EXT_TIME

signal is sampled to determine if

the time-code value is to be provided by the internal
time-counter or by the external time input

EXT_TIME_IN(7:0)

The

SEL_EXT_TIME

and the

EXT_TIME_IN(7:0)

signals must be set up prior to the rising edge of

EXT_TICK_IN

and must be held static sometime

afterwards. See section 10.4 for timing details.
If the time-code port is not being used this input

CMOS3V3

Содержание SpaceWire Router SpW-10X




























































































































































Результаты поиска

Содержание SpaceWire Router SpW-10X

Отзывы:

Похожие инструкции для SpaceWire Router SpW-10X

Бренды по названию

Популярные бренды

Atmel SpaceWire Router SpW-10X, Руководство пользователя

Результаты поиска

Содержание SpaceWire Router SpW-10X

Отзывы:

Похожие инструкции для SpaceWire Router SpW-10X

Бренды по названию

Популярные бренды