Atmel SpaceWire Router SpW-10X Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 155

background image

Ref.:

UoD_SpW-10X_

UserManual

Issue:

3.4

SpW-10X

SpaceWire Router

User Manual

Date:

11

th

July 2008

Preliminary

107

Table 9-3 GAR Table Register Description

Address Range: 32-255 (0x0000 0020 – 0x0000 00FF)

Bits Name

Reset
Value

Description Read/Write

0

RESERVED

‘0’

Reserved bit – always set to zero.

R

10:1 REQUEST

Undefined
after power
on.

Unaltered
by reset.

The request bits determine which output ports
the logical address will arbitrate for. When bit
1 is set then SpaceWire port 1 will be
requested. When bit 2 is set then SpaceWire
port 2 will be accessed and so on.

By setting more than one bit group adaptive
routing can be used, allowing the input packet
to arbitrate for more than one output port.

If a write is performed and bits 10:1 are set to
zero then the INVALID_ADDR bit will be set
and all other bits will be set to zero

Note: The configuration port (port 0) is not
accessible through logical addresses.

R/W

28:11 NOT

USED

-

-

-

29 DEL_HEAD Undefined

after power
on.

Unaltered
by reset.

Delete header: when set the leading header
byte of the input packet will be removed
before it is transferred to the output port.

R/W

30 PRIORITY

Undefined
after power
on.

Unaltered
by reset.

When a packet has a logical address with an
entry in the priority filed of this register set, the
packet will be granted access to a particular
output port in preference to packets with
priority bit set to zero.

R/W

31

INVALID_ADDR ‘1’

When the Invalid Address bit is set it indicates
that the corresponding logical address is
invalid. In this case, any packets arriving at
the router with an invalid address are spilt and
an address error is reported in the port status
register.

R/W

«
...
105
106
107
108
109
...
»

Содержание SpaceWire Router SpW-10X




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для SpaceWire Router SpW-10X

Бренд: Teletronics International Страницы: 57

Бренд: Ubiquiti Страницы: 23

Бренд: IBM Страницы: 72

Бренд: MiLAN Страницы: 155

Бренд: DPS Telecom Страницы: 80

HiGain Line Unit HLU-388

Бренд: PairGain Страницы: 7

Бренд: Intercel Страницы: 17

Бренд: Tripp Lite Страницы: 2

SDW-541-F1G-T4G

Бренд: Westermo Страницы: 20

Бренд: D-Link Страницы: 16

Бренд: Huawei Страницы: 2

Бренд: Huawei Страницы: 70

Бренд: Huawei Страницы: 51

Бренд: Huawei Страницы: 92

Бренд: Huawei Страницы: 73

Бренд: Huawei Страницы: 2

Бренд: Huawei Страницы: 2

RackSwitch G8272

Бренд: Lenovo Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды