Atlas IED Dante HPA-DAC4 Скачать руководство пользователя страница 4

Страница: 4 / 12

Owner’s Manual

HPA-DAC4

Dante

Accessory Card

AtlasIED.com

– 4 –

Specifications are subject to change without notice.

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: 800.876.3333 • Fax: 800.765.3435

HPA-DAC4 Card Installation

Note:

Accessory card installation must be done by a qualified technician.

1. Remove the HPA amplifier from the AC mains source.

Note

: In standby mode there are DC voltages

present. The HPA amp must be removed from the AC Mains source in order to prevent damage to

the card or amplifier.

2. Remove the two screws (M3 x 8mm Pan Head Black) holding the HPA Accessory blank panel.

3. Remove the ribbon cable from the cover plate.

4. Connect the accessory card to the ribbon cable by carefully aligning the ribbon cable connector to

the mating PCB connector. Do not force. If aligned correctly the cable will mate easily.

5. Carefully guide the accessory card into the slot without forcing the PCB or cable.

6. After the card is inserted and the accessory panel is flush to the chassis, align the two screw

holes and secure them together by inserting two M3 x 8mm screws.

Содержание Dante HPA-DAC4













Результаты поиска

Содержание Dante HPA-DAC4

Отзывы:

Похожие инструкции для Dante HPA-DAC4

Бренды по названию

Популярные бренды

Atlas IED Dante HPA-DAC4, Руководство пользователя

Результаты поиска

Содержание Dante HPA-DAC4

Отзывы:

Похожие инструкции для Dante HPA-DAC4

Бренды по названию

Популярные бренды