Atlas IED Dante HPA-DAC4 Скачать руководство пользователя страница 3

Страница: 3 / 12

Owner’s Manual

HPA-DAC4

Dante

Accessory Card

AtlasIED.com

– 3 –

Specifications are subject to change without notice.

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: 800.876.3333 • Fax: 800.765.3435

Audio Applications

When installed, the HPA-DAC4 converts the HPA Series amplifier into a digital audio network

amplifier and makes the HPA Series amplifier the “go to” solution for a variety of applications

including:

• Restaurants

• Government facilities

• Schools

• Industrial facilities

• House of worship

Selecting the dBFS Reference on the HPA-DAC4

The HPA-DAC4 comes with a choice of dBFS (Decibels Full Scale) gain selections of 0dBFS = 10dBu

and 0dBFS = 20dBu. Factory default for the card is 0dBFS = 20dBu. There is a 2-pin header on the

card that is the OdBFS gain selection. When a shunt is applied to the header, the 0dBFS = 20dBu

setting is engaged. When the shunt is removed the setting is 0dBFS = 10dBu. Most pro audio

equipment gains are in the range of 20dBu – 24dBu. Read the entire manual to understand these

settings.

Matching Gain from a Source to the HPA Series Amplifier In a Dante

Network

Understanding the gain structure is very important to avoid clipping the audio signal or amplifier

output. There are three potential ways to clip the signal chain.

Amplifier Input Clipping

- This occurs when the applied input signal exceeds the maximum input

level of the amplifier input stage.

Amplifier Output Clipping

- Driving the amplifier to maximum output level using the factory default

requires 0dBu or .775V of signal when the channel level control is set to maximum or the all up fully

clockwise.

Note:

AtlasIED recommends the level to be set with the level being controlled from

the source. Exceeding .775V or 0dBu level will cause the amplifier output stage to clip.

Digital Clipping

- This occurs when the 0dBFS levels are exceeded. This is very important to

understand. Several examples are provided to help understand digital to analog gain structure.

Note:

AtlasIED recommends to always place a limiter set for 0dB in the signal path prior to the

Network Output of the transmitting device. This is the best way to prevent clipping the HPA-DAC4.

Shunt on 0dBFS = 20dBu, factory default

Shunt off 0dBFS = 10dBu

Содержание Dante HPA-DAC4













Результаты поиска

Содержание Dante HPA-DAC4

Отзывы:

Похожие инструкции для Dante HPA-DAC4

Бренды по названию

Популярные бренды

Atlas IED Dante HPA-DAC4, Руководство пользователя

Результаты поиска

Содержание Dante HPA-DAC4

Отзывы:

Похожие инструкции для Dante HPA-DAC4

Бренды по названию

Популярные бренды