Safety Information
ETP TBP91-80-13
4
© Atlas Copco Industrial Technique AB - 9834 5051 00
• change of air- or electrical connections
• change in line ergonomics, process, quality procedures
or practices
• changing of operator
• any other change that influences the result of the tighten-
ing process
The check should:
• Ensure that the joint conditions have not changed due to
events of influence.
• Be done after initial installation, maintenance or repair
of the equipment.
• Occur at least once per shift or at another suitable fre-
quency.
EU DECLARATION OF CONFORMITY
We,
Atlas Copco Industrial Technique AB
, S-105 23
STOCKHOLM SWEDEN, declare under our sole responsi-
bility that the product (with name, type and serial number,
see front page) is in conformity with the following Direc-
tive(s):
2006/42/EC, 2011/65/EU, 2014/30/EU, 2014/53/EU
Harmonized standards applied:
EN 300 328 V2.1.1, EN 300 440 V2.1.1, EN 301 489-1
V2.1.1, EN 301 489-17 V3.1.1, EN 301 893 V2.1.1, EN
50566:2017, EN 55014-1:2017, EN 55014-2:2015, EN
61000-6-1:2007, EN 61000-6-2:2005, EN
61000-6-3:2007+A1, EN 61000-6-4:2007+A1, EN
62841-1:2015, EN 62841-2-2:2015+AC1
Authorities can request relevant technical information from:
Product Compliance Manager, Atlas Copco Industrial Tech-
nique AB, S-105 23 Stockholm Sweden
Stockholm, 18 February 2021
Carl von Schantz, Managing Director
Signature of issuer
Noise and Vibration Declaration Statement
• Sound pressure level 75 dB(A) , uncertainty 3 dB(A), in
accordance with EN 62841-1 EN 62841-2-2.
• Sound power level <80 dB(A) , uncertainty 3 dB(A), in
accordance with EN 62841-1 EN 62841-2-2.
• Vibration total value <2.5 m/s
2
, uncertainty - m/s
2
, in ac-
cordance with ISO28927-2.
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. These declared val-
ues are not adequate for use in risk assessments and values
measured in individual work places may be higher. The ac-
tual exposure values and risk of harm experienced by an indi-
vidual user are unique and depend upon the way the user
works, the workpiece and the workstation design, as well
upon the exposure time and the physical condition of the
user.
We,
Atlas Copco Industrial Technique AB
, cannot be held
liable for the consequences of using the declared values, in-
stead of values reflecting the actual exposure, in an individ-
ual risk assessment in a work place situation over which we
have no control.
This tool may cause hand-arm vibration syndrome if its use
is not adequately managed. An EU guide to managing hand-
arm vibration can be found by accessing
and selecting 'Tools' then 'Legis-
lation'.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
WEEE
Information concerning
Waste of Electrical and Electronic
Equipment
(WEEE):
This product and its information, meets the requirements of
the WEEE Directive (2012/19/EU), and must be handled in
compliance with the directive.
The product is marked with the following symbol:
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE Directive. The entire
product, or the WEEE parts, can be sent to your “Customer
Center” for handling.
RF Exposure Statement
This portable transmitter has been tested and found to com-
ply with FCC General Population RF Radiation Exposure
limits set forth for an uncontrolled environment and meets
the FCC radio frequency (RF) Exposure Guidelines. The an-
tenna used for this device must not be co-located or operating
in conjunction with any other antenna or transmitter.
