ETP SRB81-300-20-D
Safety Information
© Atlas Copco Industrial Technique AB - 9834 6192 00
5
The device is only in compliance if no changes or modifica-
tions are made to the device. The antenna is fixed to the de-
vice and no change in antenna or fixation of the antenna is
acceptable and such modification is considered to violate the
Compliance Statement.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pur-
suant to part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio com-
munications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the follow-
ing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is con-
nected.
• Consult the dealer or an experienced radio/TV tech-
nician for help.
ISED Compliance Statement:
This device complies with: CAN ICES-1 (B)/NMB-1(B)
(English) This device complies with Industry Canada’s li-
cence-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including inter-
ference that may cause undesired operation of the device.
(French) Le présent appareil est conforme aux CNR d’Indus-
trie Canada applicables aux appareils radio exempts de li-
cence. L’exploitation est autorisée aux deux conditions suiv-
antes:
1) l’appareil ne doit pas produire de brouillage;
2) l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromet-
tre le fonctionnement.
RF Exposure Statement
This portable transmitter has been tested and found to com-
ply with FCC General Population RF Radiation Exposure
limits set forth for an uncontrolled environment and meets
the FCC radio frequency (RF) Exposure Guidelines. The an-
tenna used for this device must not be co-located or operating
in conjunction with any other antenna or transmitter.
Information Regarding Article 33 in REACH
The European Regulation (EU) No. 1907/2006 on Registra-
tion, Evaluation, Authorization and restriction of Chemicals
(REACH) defines among other things requirements related to
communication in the supply chain. The information require-
ment applies also to products containing so called Substances
of Very High Concern (the “Candidate List”). On 27 June
2018 lead metal (CAS nr 7439-92-1) was added to the Candi-
date List.
In accordance with the above this is to inform you that cer-
tain electrical and mechanical components in the product
may contain lead metal. This is in compliance with current
substance restriction legislation and based on legit exemp-
tions in the RoHS Directive (2011/65/EU). Lead metal will
not leak or mutate from the product during normal use and
the concentration of lead metal in the complete product is
well below the applicable threshold limit. Please consider lo-
cal requirements on the disposal of lead at product end of
life.
Regional Requirements
WARNING
This product can expose you to chemicals including
lead, which is known to the State of California to cause
cancer and birth defects or other reproductive harm. For
more information go to
https://www.p65warnings.ca.gov/
UK DECLARATION OF CONFORMITY
We,
Atlas Copco Industrial Technique AB
,
SE-105 23 STOCKHOLM SWEDEN, declare
under our sole responsibility that the product
(with name, type and serial number, see front
page) is in conformity with the following UK
Regulation(s):
S.I. 2008/1597, S.I. 2012/3032, S.I. 2017/1206
Designated Standards applied:
EN 300 328 V2.2.2, EN 300 440 V2.1.1, EN
300 440 V2.1.1, EN 301 489-1 V2.1.1, EN 301
489-1 V2.1.1, EN 301 489-17 V3.1.1, EN 301
489-17 V3.1.1, EN 55014-1:2017, EN
55014-1:2017, EN 55014-2:2015, EN
55014-2:2015, EN 61000-6-2:2019, EN
61000-6-2:2019, EN 61000-6-3:2007+A1:2011,
EN 61000-6-3:2007+A1:2011, EN
61000-6-4:2007+A1:2011, EN
61000-6-4:2007+A1:2011, EN 62841-1, EN
62841-1, EN 62841-2-2, EN 62841-2-2
Authorities can request relevant technical information from:
Product Compliance Manager, Atlas Copco Industrial Tech-
nique AB, SE-105 23 Stockholm Sweden
Stockholm, 1 December 2021
Carl von Schantz, Managing Director
