ATIKA T 250 ECO, Оригинальное руководство пользователя

Страница: 22 / 94

20
„
Ensure that cut off pieces are not caught up by the saw
blade and projected away.
„ Do not remove splinters, chips and waste from the
hazardous area of the saw blade by hand .
„
It is not permissible to use wobble devices and g roove
milling tools .
„ Always keep sufficient distance to the saw blade. Maintain
sufficient distance from driven components during
operation.
„
The saw blade runs after . Wait until the saw blade has
come to a standstill before remove splinters, chips and
waste.
„ Do not slow the saw blade down by applying lateral
pressure to it.
„
Switch the machine off and remove the mains plug from
the socket when
−
carrying out repair works
−
maintenance and cleaning
−
removal of faults (this also includes the removal of
jammed splinters)
−
checks of connecting lines, whether these are knotted or
damaged
−
Transporting the saw
−
Changing the saw blade
−
leaving the saw unattended (even during short
interruptions)
„
Look after your saw with care:
−
Keep your tools sharp and clean in order to be able to
work better and safer.
−
Follow the maintenance instructions and the
instructions for tool exchange.
−
Keep handles dry and free of oil and grease.
„ Check the machine for possible damage :
−
Before further use of the machine the protection
devices or slightly damaged parts must be checked
carefully for their proper and intended function.
−
Check whether the movable parts function perfectly
and do not stick or whether the parts are damaged. All
parts must be correctly installed and fulfil all conditions
to ensure perfect operation of the saw
−
Damaged guards and parts must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
−
Damaged or illegible security labels have to be
replaced.
„
Do not allow any tool key to be plugged in !
„ Before switching on, check always that wrenches and
adjusting tools are removed.
„
Store unused equipment in a dry, locked place out of the
reach of children.
Electrical safety
„
Design of the connection cable according to IEC 60 245 (H
07 RN-F) with a core cross-profile section of at least
−
1.5 mm2 for cable lengths up to 25m
−
2.5 mm2 for cable lengths over 25m
„
Long and thin connection lines result in a potential drop .
The motor does not reach any longer its maximal power; the
function of the device is reduced.
„
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
„ Protect yourself against electric shocks . Avoid touching
earthed parts with your body.
„
The connector of the connection cable must be splash-
proof .
„ Wind off completely the cable when using a cable drum.
„ Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges . Do
not use the cable to pull the plug from the socket.
„
Regularly check the saw cable and if damaged, have it
renewed by a recognised skilled electrician.
„ When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
„
Regularly check the extension cables and replace them if
they are damaged.
„ Do not use any defective connection cables .
„ When working outdoors, only use extension cables
especially
approved and appropriately labelled for outdoor
use.
„
Do not set up any provisional electrical connections .
„ Never bypass protective devices or deactivate them.
„ Only hook up the machine by means of a f ault-current
circuit breaker (30 mA).
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service
points.
Use only original spare parts and accessorie parts .
Accidents can arise for the user through the use of other
spare parts. The manufacturer is not liable for any damage
or injury resulting from such action.
Before the first commissioning
L
To achieve flawless functioning of the machine, please
follow the instructions listed:
ƒ
Place the saw in a place that fulfils the following conditions:
− secured against slipping
− free of vibrations
− even
−
free of tripping hazards
−
adequate light