19
Safety instructions
Wood processing machines can be dangerous when used
improperly. The use of electrical tools requires the
observation of basic safety precautions to eliminate risk of
fire, electrical shock and personal injuries.
Before commissioning this product, read and keep to the
following advice. Also observe the preventive regulations
of your professional association and the safety provisions
applicable in the respective country, in order to protect
yourself and others from possible injury.
L
Pass the safety instructions on to all persons who work
with the machine.
L
Keep these safety instructions in a safe place.
Make yourself familiar with the equipment before using
it, by reading and understanding the operating
instructions.
Be observant. Attend to what you do. Start working with
rationality. Do not use the device when you are tired or
under the influence of drugs, alcohol or medicaments.
One moment of carelessness when using the device
can result in serious injuries.
Avoid unusual posture. Provide a
safe standing position
and keep at any time the
balance
. Do not lean forward.
Wear suitable
work clothes
:
−
do
not
wear loose-fitting clothes or
jewellery
; they can
catch in moving parts.
−
slip-
proof shoes
−
wear a
hair-net
if your hair is long
Wear protective
clothing
:
−
ear protection
(sound pressure levels at the workplace
usually exceed 85 dB(A)
−
safety goggles
−
Dust mask
with work activities generating dust
−
Gloves
when replacing the saw blade
Only
operate
the circular saw on a
−
solid
−
level
−
slip-free
−
vibration free surface
Keep your
workplace
in an
orderly condition
! Untidiness
can result in accidents.
Take into consideration
environmental influences
:
−
Do not expose the saw to
rain
.
−
Do not use the saw in a
damp or wet environment
.
−
Provide for good
illumination
.
−
Do not use the saw near to
flammable liquids or
gases
.
−
The
wood dust
generated during operation impedes the
necessary view and is harmful to health to some degree.
If the machine is not used in the open air, a shavings
exhausts must be attached to both
exhaust outlets
(e.g. small transportable dust remover).
Never
leave the saw
unattended
.
Persons under the age of 18
must not operate the circular
saw. An exception is
youngsters under the age of 16
within the scope of their
vocational training under
supervision
.
Keep
other persons
away.
Do not allow other persons,
especially children
, to touch
the
tool or cable
.
Keep them away from your working area.
Take up a
working position
, in which you are always to the
side of the saw blade outside of the cutting level.
Assume the correct
working position
. Place yourself in
front at the operator side, in front of the saw to the right of
the cutting level.
Remove
all nails and metal objects from the work piece
prior to sawing.
Pay attention
that the work piece does not contain any
cables, ropes, cords or the like.
Only begin cutting after the saw blade has reached its
required rotational speed
.
Do not overload the machine! You work better and safer in
the given
performance range
.
Only operate the machine with complete and correctly
attached
safety equipment
and do not alter anything on the
machine that could impair the safety.
Replace
the bench insert if the sawing gap is worn.
Do not use any cracked saw blades or such that have
changed their shape.
Use only sharp saw blades since dull saw blades not only
increase the danger of
back kicking
but also cause
excessive load on the motor.
Do
not use saw blades made of high speed steel (HSS)
since this steel is hard and brittle; use only tools according
to EN 847-1.
The use of other tools and other accessories can signify
a risk of injury for you.
Pay attention that the saw blade conforms to the
dimensions specified under "Technical Data" and is suitable
for the work piece material.
Use the
splitting wedge provided
. It must be set so that its
distance to the tooth rim of the saw blade is no more than 5
mm above the bench.
Use only
fine-tooth saw blades
to cut thin or thin-wall work
pieces.
Only saw
one work piece at a time
. Never saw several
work pieces at the same time or do not bundle several
individual pieces together for cutting. There is danger that
individual pieces may be caught by the saw blade in an
uncontrolled manner.
Do not use the saw for purposes it is not intended for (see
intended use).
When longitudinally cutting
narrow workpieces
(distance
between the saw blade and the parallel rip fence less than
120 mm), use the
pushstick
.
To push narrow workpieces against the parallel rip fence,
use a
pushstick
.
Î
Pushsticks can be purchased in retail outlets.
Do
not use defective
pushsticks.
You work better and safer in the given performance range. It
has to be positioned in the way that the saw blade is
covered completely except for the part necessary for the
work piece machining.
Содержание T 250 ECO
Страница 5: ...3 1 ...
Страница 93: ...91 ...
