ATI Technologies WHC400 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 40

background image

ENG - Manual of installation, use and maintenance.

210-0352_libretto_WHC_ATI_eng.docx

33

Jan-19

congruent with the written one, the anomaly
activates.



This anomaly is deactivated if, in view of a new
operation towards the EEPROM, the data is
properly stored.

DISPLAYS

The message "Err." appears alternately with the message

"F096". The

flashing fault symbol is displayed.

DEVICES

Gas valve: Off.

Fan: if foreseen, a post-purge cycle is performed, then it is
deactivated.

Circulation pump: it performs a post-circulation cycle, if
foreseen, then it turns off.

FAULT F097

DESCRIPTION

Discordant values for the two NTC sensors of the
flow/safety probe.

ACTIVATION / DEACTIVATION CONDITIONS



The anomaly occurs if the safety microcontroller
detects discordant temperature values for the two
NTC sensors of the dual flow/safety probe.



The anomaly occurs if the safety microcontroller
detects congruent temperature values for the two
NTC sensors of the dual flow/safety probe.

DISPLAYS

"Err." appears alternating with the message "F097". The

flashing fault symbol and the

flashing sensor

fault symbol are displayed

DEVICES

Gas valve: Off.

Fan: if foreseen, a post-purge cycle is performed, then it is
deactivated.

Circulation pump: it performs a post-circulation cycle, if
foreseen, then it turns off.

FAULT F098

DESCRIPTION

Flow/safety double sensor interrupted or short-circuited

→

flow NTC

ACTIVATION / DEACTIVATION CONDITIONS



The anomaly occurs if the safety microcontroller
detects that the NTC of the flow / safety double
sensor is interrupted or short-circuited.



The anomaly is deactivated if the safety
microcontroller detects that the NTC of the flow /
safety double probe is no longer interrupted or
short-circuited.

DISPLAYS

The message "Err." appears alternately with the message

"F098". The

flashing fault symbol and the

sensor

fault flashing symbol are displayed.

DEVICES

Gas valve: Off.

Fan: if foreseen, a post-purge cycle is performed, then it is
deactivated.

Circulation pump: it performs a post-circulation cycle, if
foreseen, then it turns off.

FAULT F099

DESCRIPTION

Flow/safety double sensor interrupted or short-circuited

→

safety NTC.

ACTIVATION / DEACTIVATION CONDITIONS



The anomaly occurs if the safety microcontroller
detects that the NTC of the flow / safety double
probe concerning the safety is interrupted or
short-circuited.



The anomaly is deactivated if the safety
microcontroller detects that the NTC of the flow /
safety double sensor related to safety is no longer
interrupted or short-circuited.

DISPLAYS

«
...
31
32
33
34
35
...
»

Содержание WHC400









































Отзывы:

Нет отзывов

Похожие инструкции для WHC400

FCD-JTHMG80-III

Бренд: Haier Страницы: 2

Little Sea-ox FCD-JTHC40-III (E)

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 2

Бренд: Watson-Marlow Страницы: 128

Бренд: YAMADA Страницы: 14

Бренд: Dex Страницы: 24

Бренд: Enerpac Страницы: 40

Бренд: thermalpanel Страницы: 10

Бренд: DAY Страницы: 51

Бренд: Orbegozo Страницы: 85

PVR50 Flanged Series

Бренд: Continental Hydraulics Страницы: 8

PULSAR Shadow Series

Бренд: Pulsafeeder Страницы: 46

GUARDIAN Smart Sense AD250

Бренд: L.B. White Страницы: 24

Бренд: MILL Страницы: 10

DynaDrive DD60-10

Бренд: Davey Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды