ATH HEATNET KN Series Скачать руководство пользователя страница 55

Страница: 55 / 144

CONTROL METHODS

HeatNet Control V3 3.x

Page 55

DHW Method 5a: Local DHW Tank Heating using a 10k Tank Sensor.

Figure 40

Example:

DHW Heating to a Local Boiler’s Tank,– Method 5a

MASTER

MEMBER

HNET

l P

HNET

Sen

Domestic Hot

Water

Domestic Hot

Water

Tank Sensor

l P

System Pump

sio

Cold Water

Makeup

HeatNet

Supply

Make Up

Supply

Make Up

Tank Sensor

HeatNet

System

Supply

System

Return

DHW METHOD 5a: Local DHW Tank Heating Override using a 10K Type II Tank Sensor.

In DHW METHOD 5a: Local DHW Tank Heating Override, the MASTER’s

Heat Demand

input enables space heating by

energizing the system pump and maintaining the Heating Setpoint at the MASTER’s System Header Sensor using the available

MEMBERs. A MEMBER boiler will enable its local pump when called to service a heating call by the MASTER. Each

MEMBER has its

OR OVR

input jumped to enable local DHW heating using its DHW Sensor. When a DHW tank sensor calls

for heat, the local boiler goes offline from the MASTER. The boiler can disable its local pump (Programmable) and enables its

DHW pump/valve to service the local tank until the tank sensor has been satisfied. Once the call for DHW heat has been satisfied,

the boiler is placed back online for the MASTER to service the main heating loop.

Содержание HEATNET KN Series

















































































































































Результаты поиска

Содержание HEATNET KN Series

Отзывы:

ATH HEATNET KN Series, Руководство по эксплуатации, Страница: 55 / 144

Результаты поиска

Содержание HEATNET KN Series

Отзывы: