ATH HEATNET KN Series Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 144

ATH HEATNET KN Series Скачать руководство пользователя страница 101

MESSAGING & NAVIGATION

HeatNet Control V3 3.x

Page 101

On the Home screen, information on each boiler can be
accessed by pressing a boiler’s button.

Pressing The MASTER boiler’s button will bring up the
MASTER’s information screen. Information about the
boiler is presented.

In the bottom left corner, there is the Settings button which
will allow changes to be made to the operation of the boiler.
See the Settings section.

To the right of the Settings button is the Log File button.
Pressing this button will allow viewing of the log file. See
Log Entry section.

The Data Capture is to the right of the Log File button.
Similar to the Log File, the data retrieved can be customized
and recorded to a USB drive.

Pressing any of the MEMBER buttons will bring up a
MEMBER boilers informational screen. Information

available for a MEMBER boiler is limited from the
MASTER boiler. The Log File needs to be viewed on each
MEMBER boiler directly.

«
...
99
100
101
102
103
...
»

Содержание HEATNET KN Series

















































































































































Отзывы:

Нет отзывов