ATEN VM5404HA Скачать руководство пользователя страница 90

Страница: 90 / 122

VM5404HA / VM5808HA User Manual

Exporting System Settings

In the VM5404HA / VM5808HA’s web console, go to

Settings

Maintenance

System Setup

, and then click

Backup

A configuration file

begins downloading.

Note:

Account settings cannot be exported.

Importing System Settings

Make sure you have a previously saved backup file to execute the restore.

1. In the VM5404HA / VM5808HA’s web console, go to

Settings

Maintenance

System Setup

2. Click

Browse

button to locate the configuration file. Make sure you have

the correct file saved on your PC.

3. Click

Restore

to begin the restoration procedure.

Restoring Factory Defaults

To reset the VM5404HA / VM5808HA to its default settings, do the following.

1. In the VM5404HA / VM5808HA’s web console, go to

Settings

Maintenance

System Setup

2. Click the

reset to default

button on the far right and follow the on-screen

instructions to complete the procedure.

Содержание VM5404HA



























































































































Результаты поиска

Содержание VM5404HA

Отзывы:

Похожие инструкции для VM5404HA

Бренды по названию

Популярные бренды

ATEN VM5404HA, Руководство пользователя

Результаты поиска

Содержание VM5404HA

Отзывы:

Похожие инструкции для VM5404HA

Бренды по названию

Популярные бренды