ATEN CS19208 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 108

background image

59

Chapter 7

RS-232 Operation

Overview

The CS19208 / CS19216’s built-in bi-directional RS-232 serial interface
allows system control through a high-end controller or PC. RS-232 serial
operations in a CS19208 / CS19216 installation are managed via
HyperTerminal sessions on systems that are running Windows. In order to use
this feature to send commands to the CS19208 / CS19216, you must first
download and install a HyperTerminal application.

Setup

Install a HyperTerminal application on a computer that is not part of the
installation, which will be used to control the switch via the RS-232
connection. HyperTerminal applications can be download from the Internet,
and many operating systems are embedded with HyperTerminal applications.

Hardware Connection

Use a the

Firmware Upgrade Cable

provided with this unit to connect a

computer’s serial port to the Firmware Upgrade Port on the CS19208 /
CS19216’s front panel, as shown below:

Note:

The unit used in the diagram below is CS19216, the procedure for
connecting CS19208 is identical with fewer KVM ports.

Firmware Upgrade Cable

«
...
67
68
69
70
71
...
»

Содержание CS19208













































































































Отзывы:

Нет отзывов

Похожие инструкции для CS19208

SmartSwitch 9A100

Бренд: Cabletron Systems Страницы: 52

SmartSwitch 9W006

Бренд: Cabletron Systems Страницы: 34

SmartSTACK ELS100-S24TX2M

Бренд: Cabletron Systems Страницы: 102

Бренд: Cabletron Systems Страницы: 24

SmartSwitch 9000

Бренд: Cabletron Systems Страницы: 14

Бренд: Cabletron Systems Страницы: 38

Бренд: Idem Страницы: 2

DynaGST/2402G GEP-33224T-1

Бренд: UNICOM Страницы: 1

Cleveland Controls RSS-498-013

Бренд: UNICONTROL Electronic Страницы: 2

Бренд: Xantech Страницы: 2

Бренд: Abtus Страницы: 15

Бренд: Vector Страницы: 6

Бренд: Holland Страницы: 4

Бренд: N-Tron Страницы: 158

S5130S-EI series

Бренд: H3C Страницы: 67

Бренд: Fairchild Страницы: 20

INTEGRAL Series

Бренд: DAS AUDIO Страницы: 45

Бренд: Velleman Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды