ATD Tools ATD-10556 Скачать руководство пользователя страница 2

Страница: 2 / 16

Table of Contents

SPECIFICATIONS --------------------------------------------------------------------------------------------------- 2

IMPORTANT SAFETY RULES------------------------------------------------------------------------------------3

KNOW YOUR BENCH GRINDER ------------------------------------------------------------------------- 4

OPERATING INSTRUCTIONS-----------------------------------------------------------------------------5--10

MAINTENANCE ----------------------------------------------------------- ------------------------------11

TROUBLESHOOTING -------------------------------------------------- ----------------------------1213

EXPLODED VIEW AND PARTS LIST---------------------------------------------------------------------14,15

WARRANTY --------------------------------------------------------------------------------------------------- -------16

Specifications

Model #

ATD-10558

Serial #:

Motor Type:

Induction

Motor Ratings:

120 V AC, 4.8 A, 60 Hz

3/4 HP

Wheel Diameter:

8” (20 cm)

Wheel Width:

1” (25.4 mm)

Arbor Hole:

5/8” (16 mm)

No load Speed:

3450 RPM

Wheel Grits:

36 (Coarse)

60 (Medium)

Model #

ATD-10556

Serial #:

Motor Type:

Induction

Motor Ratings:

120 V AC, 2.8 A, 60 Hz

Horsepower:

1/2 HP

Wheel Diameter:

6” (15 cm)

Wheel Width:

3/4" (20 mm)

Arbor Hole:

1/2" (13 mm)

No load Speed:

3450 RPM

Wheel Grits:

36 (Coarse)

60 (Medium)

Horsepower:

Содержание ATD-10556

















Результаты поиска

Содержание ATD-10556

Отзывы:

Похожие инструкции для ATD-10556

Бренды по названию

Популярные бренды

ATD Tools ATD-10556, Инструкция по эксплуатации

Результаты поиска

Содержание ATD-10556

Отзывы:

Похожие инструкции для ATD-10556

Бренды по названию

Популярные бренды