background image

I n s t a l l a t i o n   c o n t ’ d

4

SCM200/300ASL/P4

Diagram 1 - input connection pins

Diagram 3 - balanced cable

Diagram 4 - unbalanced cable

Pin 1, Screen

Pin 2, Signal (hot)

Two Core Screened Cable

Pin 3, Signal (return)

3 Pin Male XLR

Connector

3 Pin Female XLR

Connector

To Monitor Input

Hot

Return

Screen

To Source Output

Diagram 2 - speaker plug

1

2

3

1

2

3

Two Core Screened Cable

3 Pin Male XLR

Connector

Phono (RCA)

Connector

To Monitor Input

Hot

Return

Screen

To Source Output

1

2

3

5 . S y s t e m   C o n n e c t i o n s

Three cable connections are required for each P4

and monitor: one for mains power, one for the

audio signal and one for the speaker cable.

The mains cable is specifically supplied to comply

with local statutory safety approvals and

alternatives should not be substituted. If you intend

to use your monitors in an alternative territory

please contact ATC for advice. The mains

connection must always be earthed.

The signal cable and plug (not necessarily supplied)

should be of a good quality and XLR terminated.

Poor cable and plug quality will compromise the

performance of your monitors.The signal input pin

configuration is illustrated in Diagram 1.

Custom made 5 metre speaker cables and plugs

are supplied as standard with the P4. Speaker

cables of up to 10 metres are available. Runs up to

20 metres may be made up by splicing heavier

gauge (4mm

2)

cable to 10 metre lengths.The splice

point should be 0.5 metres before the connector.

The 8-pin speaker connector scheme is illustrated

in Diagram 2.

6 . S i g n a l   C a b l e   O p t i o n s

Balanced cable configuration is the preferred

option, however unbalanced connection is

possible. Diagrams 3 and 4 illustrate the signal

cable connections required for each option.

Balanced (XLR to XLR) connection offers lower

noise and better immunity to “hum” pick-up.

Unbalanced (XLR to Phono or Two Pole Jack)

connection carries risk of hum caused by multiple

signal earths.

Hum problems resulting from unbalanced

connection may be reduced by making ONE of the

following modifications to the signal cable

connections: If the driving preamplifier (or desk) is

“double insulated” (i.e. has no mains earth),

disconnect the signal cable screen at the RCA

Phono plug end. Alternatively, disconnect the signal

cable screen at the XLR end.This second option will

make the source the reference signal earth.

A

H

B

C

D

E

F

G

Pin

Connection

A

LF 1 Positive

B

LF 2 Positive

C

MF Positive

D

HF Positive

E

HF Negative

F

MF Negative

G

LF 1 Negative

H

LF 2 Negative

Содержание P4










Отзывы: