manualshive.com logo in svg

AT&T SPIRIT 308, Руководство администратора

Поделиться
Скачать
AT&T SPIRIT 308 Скачать руководство пользователя страница 24

Storing System  SpeedCall  Numbers

STEP 1 SET ADMINISTRATION SWITCH TO “ON”
Set the system administration switch on the controller to ON (see the drawing on page 3.)

STEP 2 PRESS INTERCOM BUTTON. PRESS SPEAKER
Working at telephone set 10, 

press an INTERCOM button that is not busy. Lift the receiver

(or press SPEAKER). INTERCOM times out after five seconds. You must lift the receiver or

press SPEAKER within those five seconds or start the procedure over again at STEP 2.

STEP 3 ENTER CUSTOMIZATION
Dial * 0 (zero)

STEP 4 CHOOSE SYSTEM SPEEDCALL
Dial 3

STEP 5 DIAL NUMBER
Dial a number you wish to store in the system SpeedCall  memory. A total of 16 digits, including
pauses and one flash, may be stored as one number.

NOTE: Press the HOLD/PAUSE button to enter a 1½ second pause in the number (i.e., to wait for
a dial tone or access tone). If your system is part of a PBX/Centrex system you may store the outside
access code as part of the number. If the line is customized as a PBX/Centrex line and the access
code is entered in system customization, the system will automatically insert a pause after the code

when you use your SpeedCall numbers.

STEP 6 PRESS MEMORY

STEP 7 ENTER TWO-DIGIT CODE
Enter the two-digit code you wish to assign to the number you have stored. Remember, code
numbers 30 through 79 are for unrestricted numbers 

that can be dialed by any user in your

system, regardless of any outside service restrictions that may be customized on any one
telephone set. Code numbers 80 through 99 are restricted according to the outside service you
customize for each telephone (see Outside Service, page 16).

If you use a code that is already in use for another number, the new number will be
stored over the old number and the old number will be lost. If you enter an invalid code
(a code other that 30-99) you will hear the error tone, which is a series of alternating high
and low beeps. This means you will have to start over again at STEP 5, dialing the telephone
number. When you have successfully stored a number in the system  SpeedCall  memory you
will hear a confirmation tone (three short beeps).

When you hear the confirmation tone you may continue to store numbers in the system
SpeedCall  memory by going back to STEP 5 and dialing a new number. If you are finished
storing numbers and wish to exit the procedure, hang up the receiver (or press SPEAKER
if you were using the speakerphone) and return the administration switch to OFF.

Erasing a Number from the System  SpeedCall  Memory

You may enter a new number over an old number instead of erasing the old number. If you
wish to simply erase a number, follow steps 1 through 4 of the above procedure. At STEP 5,
instead of entering a number, press the MEMORY button. Enter the code of the number you want
to erase. A confirmation tone indicates your success. You may continue erasing, or you may
enter a new number by going back to STEP 5 of the procedure. If you wish to exit the
procedure, hang up the receiver (or press SPEAKER if you were using the speakerphone) and
return the administration switch to OFF.

Administration Manual 23

Содержание SPIRIT 308


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды