Asyril Asycube Скачать руководство пользователя

Страница: 33 / 41

Asycube - Asyril SA

Operating Manual

Transportation, handling and installation

v1.7

FO 32.03.118

Operating Manual

Asycube

- Asyril SA

33/41

Installation and storage environment

3.4.

WARNING !

The Asycube must be mounted on a smooth, flat and strong surface. Ensure yourself

that the Asycube is not submitted to mounting flexure. Failure to do so would degrade

feeder performance.

Installation environment

3.4.1.

The Asycube can be used under following conditions:

Working temperature: +5°C to +40°C

WARNING !

note that variations of temperature might affect the precision of the robot, especially if

precisions below 10 microns are necessary

Humidity: 30% to 95% max. non-condensing

WARNING !

In the case of extreme humidity, note that it might affect the global performances of the

cell.

Avoid extreme electromagnetic waves, ultraviolet rays and radiation.

Avoid using the product in a place where the main unit or controller may be exposed to water

or oil droplets.

Clean room application: cleanliness class ISO7 and ISO8

WARNING !

Do not use the product in an atmosphere of corrosive gases. Rust may form and reduce

the structural strength of the product.

Storage environment

3.4.2.

The storage environment should be similar to the operating environment. In addition, you

should protect the Asycube against dust

Содержание Asycube










































Результаты поиска

Содержание Asycube

Отзывы:

Похожие инструкции для Asycube

Бренды по названию

Популярные бренды

Asyril Asycube, Руководство по эксплуатации

Результаты поиска

Содержание Asycube

Отзывы:

Похожие инструкции для Asycube

Бренды по названию

Популярные бренды