Asus AAEON GENESYS-KBU6 Скачать руководство пользователя страница 8

Страница: 8 / 98

Preface

VIII

3.5

”

mp
act

ard

ENE

S-

KBU6

FCC Statement

This device complies with Part 15 FCC Rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received including interference that may cause

undesired operation.

Caution:

There is a danger of explosion if the battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries

according to the manufacturer’s instructions and your local government’s recycling or

disposal directives.

Attention:

Il y a un risque d’explosion si la batterie est remplacée de façon incorrecte.

Ne la remplacer qu’avec le même

modèle ou équivalent recommandé par le constructeur.

Recycler les batteries usées en accord avec les instructions du fabricant et les directives
gouvernementales de recyclage.

Содержание AAEON GENESYS-KBU6



































































































Результаты поиска

Содержание AAEON GENESYS-KBU6

Отзывы:

Похожие инструкции для AAEON GENESYS-KBU6

Бренды по названию

Популярные бренды

Asus AAEON GENESYS-KBU6, Руководство пользователя

Результаты поиска

Содержание AAEON GENESYS-KBU6

Отзывы:

Похожие инструкции для AAEON GENESYS-KBU6

Бренды по названию

Популярные бренды