Asus AAEON GENESYS-KBU6 Скачать руководство пользователя страница 52

Страница: 52 / 98

Chapter 3

–

AMI BIOS Setup

3.5

”

mp
act

ard

ENE

S-

KBU6

3.1 System Test and Initialization

The board uses certain routines to perform testing and initialization. If an error, fatal or

non-fatal, is encountered, a few short beeps or an error message will be outputted. The

board can usually continue the boot up sequence with non-fatal errors.

The system configuration verification routines check the current system configuration

against the values stored in the CMOS memory. If they do not match, an error message

will be outputted, in which case you will need to run the BIOS setup program to set the

configuration information in memory.

There are three situations in which you will need to change the CMOS settings:

You are starting your system for the first time

You have changed your system

’

s hardware

The CMOS memory has lost power and the configuration information is erased

The system

’

s CMOS memory uses a backup battery for data retention, which is to be

replaced once emptied.

Содержание AAEON GENESYS-KBU6



































































































Результаты поиска

Содержание AAEON GENESYS-KBU6

Отзывы:

Похожие инструкции для AAEON GENESYS-KBU6

Бренды по названию

Популярные бренды

Asus AAEON GENESYS-KBU6, Руководство пользователя

Результаты поиска

Содержание AAEON GENESYS-KBU6

Отзывы:

Похожие инструкции для AAEON GENESYS-KBU6

Бренды по названию

Популярные бренды