background image

 

 

GOVERNMENT REGULATIONS 

This device complies with the requirements of Industry Canada (IC) - Management of Radio Frequencies, as specified in document CNR-210. 
Its use is authorized only on a no-interference, no-protection basis; in other words, this device must not be used if it is determined that it 
causes harmful interference to services authorized by IC. In addition, the user of this device must accept any radio interference that may be 
received, even if this interference could affect the operation of the device. 

 
 
 
 

 
 

This device complies with Part 15 of the FCC rules.  
Operation is subject to the following two conditions: 

(1)   this device may not cause harmful interference and 
(2)   this device must accept interference that may cause undesired operation. 

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These 
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television, which can be determined by turning the equipment OFF and ON, the user is 
encouraged to try to correct the interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the distance between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

 

Consult the dealer or an experienced radio / TV technician for help. 

 

Warning: 

Changes or modifications not expressly approved by <manufacturer> could void the user's authority to operate the 
equipment. 

 

 

 

 

Inc.

 

1164, Route 220 

St-Élie d’Orford (Québec) Canada 

J0B 2S0

 

 

 

E L E C T R O N I C   C O R P .

 

 

516A Elm  Street 

M anchester, NH 03101 

USA

 

 

 

www.astroflex.com 

 

Содержание 701U













Отзывы: