ASTRO Direct Digital X-QAM twin 3, Руководство по эксплуатации

Страница: 3 / 16

Contents
Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
Pictographs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4
1 Description
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4
2 Pre – configuration / Cabling
. . . . . . . . . . . . . . . . . . Page 5
3 Programming with the HE programming software
. . Page 5
3.1 Pre – configuration of the HE programming software . Page 5
3.2 Activating the NIT processing . . . . . . . . . . . . . . Page 6
3.3 Programming the card parameters . . . . . . . . . . Page 6
3.4 Testing the input signal quality . . . . . . . . . . . . . Page 7
3.5 Level adjustment . . . . . . . . . . . . . . . . . . . . . . . . Page 7
3.6 Setting the PID filter . . . . . . . . . . . . . . . . . . . . . Page 8
3.7 PID remapping . . . . . . . . . . . . . . . . . . . . . . . . . Page 8
3.8 Error messages . . . . . . . . . . . . . . . . . . . . . . . . Page 8
3.9 Changing the Operator – ID . . . . . . . . . . . . . . . Page 9
4 Basics of programming with the KC 3
. . . . . . . . . . Page10
4.1 Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page10
4.2 Order of programming . . . . . . . . . . . . . . . . . . . Page10
4.3 Store . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page10
5 Programming with the KC 3 . . . . . . . . . . . . . . . . . . . Page11
5.1 Parameters of the base unit /
Choosing a slot . . . . . . . . . . . . . . . . . . . . . . . . . Page11
5.1.1 Adjusting the bus address . . . . . . . . . . . Page11
5.1.2 Choosing the slot . . . . . . . . . . . . . . . . . . Page11
5.2 Adjusting the SAT input parameters . . . . . . . . . Page11
5.2.1 Adjusting the SAT – IF input frequency . Page11
5.2.2 Choosing the input . . . . . . . . . . . . . . . . . Page11
5.2.3 Adjusting the symbol ratio . . . . . . . . . . . Page12
5.2.4 Adjusting the Viterbi ratio . . . . . . . . . . . . Page12
5.3 Setting the RF output parameters . . . . . . . . . . Page12
5.3.1 Setting the RF output frequency . . . . . . . Page12
5.3.2 Adjusting the output data ratio . . . . . . . . Page12
5.3.3 Setting the type of modulation . . . . . . . . Page13
5.3.4 Switching – off the output signal . . . . . . . Page13
5.3.5 Inverting the output spectrum . . . . . . . . . Page13
5.3.6 Error messages . . . . . . . . . . . . . . . . . . . Page13
5.3.7 Level adjustment of the X-QAM x – card . . Page13
6 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page14
7 Short overview of KC 3 programming steps . . . . . Page15
Contents Contents
3