./4%$)!'2!-3),,5342!4)/.3!2%./44/3#!,%
9
)../6!4)6%(%!24(02/$5#43s$)2%#46%.4'!3&)2%0,!#%3-ONTEBELLO$,8-ONTEBELLO$,8#$ s).34!,,!4)/.).3425#4)/.3
TYPICAL INSTALLATION SEQUENCE
4HETYPICALSEQUENCEOFINSTALLATIONISOUTLINED
BELOW(OWEVEREACHINSTALLATIONISUNIQUEAND
MAYRESULTINVARIATIONSTOTHESTEPSDESCRIBED
3EETHE0AGENUMBERSREFERENCESINTHEFOLLOW
-
ing steps for detailed procedures.
Step 1.
(
Page 9
)
Construct the appliance
framing. Position the appliance within
the framing and secure with nailing
BRACKETS
Step 2.
(
Page 11
)
Route gas supply line to the
right side.
Step 3.
(
Page 12
)
Install the vent system and
EXTERIORTERMINATION
Step 4.
(
Page 21
)
Connect 120 VAC electrical
power to the appliance receptacle.
Step 5.
(
Page 23
)
Remove glass door assem-
BLY
Step 6.
(
Page 23
)
-AKE CONNECTION TO GAS
supply.
Step 7.
(
Page 23
)
Verifying appliance opera-
tion.
Step 8.
(
Page 24
)
)NSTALLlREBOXLINERPANELS
LOGSANDGLOWINGEMBERS
OR
CONTEMPORARYBURNERmOORKITPORCE
-
lain panels, and media.
Step 9.
(
Page 26
)
)NSTALLGLASSDOORASSEMBLY
Step 10.
(
Page 26
)
!DJUST BURNER TO ENSURE
proper flame appearance.
Step 11.
(
Page 29
)
Attach safety in operation
warnings.
Left Side Front Corner of Fireplace Shown
(Right Side Requirements the Same)
Unit Being Secured By Its Nailing Flanges
To The Framing
NOTE: The nailing flanges, combustible members and
screw heads located in areas directly adjacent to
the nailing flanges, are EXEMPT from the 1/2” clear-
ance to combustible requirements for the firebox
outer wrapper. Combustible framing may be in direct
contact with the nailing flanges and may be located
closer than 1/2” from screw heads and the firebox
wrapper in areas adjacent to the nailing flanges.
Frame the opening to the exact dimensions speci-
fied in the framing details of this manual.
Unit Being Secured by Its Nailing
Flanges to the Framing
Unit Being Secured by Its Nailing
Flanges to the Framing
Note: The nailing flanges, combustible members
and screw heads located in areas directly adjacent
to the nailing flanges, are EXEMPT from the 1/2”
clearance to combustible requirements for the
firebox outer wrapper. Combustible framing may be
in direct contact with the nailing flanges and may
be located closer than 1/2” from screw heads and
the firebox wrapper in areas adjacent to the nailing
flanges. Frame the opening to the exact dimensions
specified in the framing details of this manual.
Use Top Flange For
1/2” Thick Drywall
Use Bottom Flange For
5/8” Thick Drywall
Front Of
Fireplace
Use Center Flange
For Flush Mount
Left Side Front Corner of Fireplace Shown
(Right Side Requirements the Same)
Unit Being Secured By Its Nailing Flanges
To The Framing
Step 1. FRAMING
&RAMETHESEAPPLIANCESASILLUSTRATEDIN
Figure
11 on Page 10
,
UNLESSTHEAPPLIANCEISTOBE
installed in a corner
.
See
Figure 12 on Page
11
for corner framing installations. All framing
details must allow for a minimum clearance to
COMBUSTIBLE FRAMING MEMBERS AS SHOWN IN
Table 5 on Page 8
.
)FTHEAPPLIANCEISTOBEELEVATEDABOVEmOOR
LEVEL A SOLID CONTINUOUS PLATFORM MUST BE
CONSTRUCTEDBELOWTHEAPPLIANCE
(EADERS MAY BE IN DIRECT CONTACT WITH THE
APPLIANCE TOP SPACERS BUT MUST NOT BE SUP
-
PORTEDBYTHEMORNOTCHEDTOlTAROUNDTHEM
!LLCONSTRUCTIONABOVETHEAPPLIANCEMUSTBE
self-supporting,
DO NOT
use the appliance for
structural support.
4HE lREPLACE SHOULD BE SECURED TO THE SIDE
FRAMING MEMBERS USING THE UNITgS NAILING
mANGESONETOPANDBOTTOMONEACHSIDEOF
THElREPLACEFRONTSEE
Figure 10
)
.
5SEDNAILS
ORTHEIREQUIVALENT
Figure 10
DETAILED INSTALLATION STEPS
The appliance is shipped with all gas
controls and components installed and pre-
wired.
2EMOVETHESHIPPINGCARTONEXPOSINGTHE
front glass door on the valve access side.
2. Using a Phillips screwdriver, unfasten two
SCREWSLOCATEDATTHETOPOFTHEGLASS
FRAME
see
Figure 46 on page 26
).
Tilt the
top of the glass frame away from the unit.
,IFTITCAREFULLYOFFTHEBOTTOMDOORTRACK
and set the door aside, protecting it from
inadvertent damage.
WARNING
Failure to position the parts in
accordance with these diagrams
or failure to use only parts specifi-
cally approved with this appliance
may result in property damage or
personal injury.
AVERTISSEMENT
Risque de dommages ou de
blessures si les pièces ne sont
pas installées conformément à
ces schémas et ou si des pièces
autres que celles spécifiquement
approuvées avec cet appareil sont
utilisées.
