./4%$)!'2!-3),,5342!4)/.3!2%./44/3#!,%
23
)../6!4)6%(%!24(02/$5#43s$)2%#46%.4'!3&)2%0,!#%3-ONTEBELLO$,8-ONTEBELLO$,8#$ s).34!,,!4)/.).3425#4)/.3
WARNING
Never use an open flame to
check for leaks.
4URNONGASSUPPLYANDTESTFORGASLEAKSUSINGA
GASLEAKTESTSOLUTIONALSOREFERREDTOASBUBBLE
LEAKSOLUTION
NOTE:
Using a soapy water solution is an
effective leak test solution but it is not recom-
mended, because the soap residue that is left
on the pipes/fittings can result in corrosion
over time.
Step 5. REMOVE GLASS DOOR FRAME
2EMOVETHEGLASSDOORASSEMBLY3EE
Installa-
tion and Removal of Glass Door
on
Page 26
.
Step 6. CONNECTING GAS LINE
!LLCODESREQUIREASHUTOFFVALVEMOUNTEDINTHE
supply line. The orientation of the shut-off valve
should face the front.
Figure 36
illustrates two
methods for connecting the gas supply. A Sedi-
ment Trap is recommended to prevent moisture
ANDDEBRISINGASLINEFROMDAMAGINGTHEVALVE
4HEmEXLINEMETHODISACCEPTABLEINTHE53!
where local codes permit, however, Canadian
REQUIREMENTSVARYDEPENDINGONLOCALITY)NSTAL
-
LATIONMUSTBEINCOMPLIANCEWITHLOCALCODES
4HESEAPPLIANCESAREEQUIPPEDWITHAGASmEX
line for use in connecting the unit to the gas
line. See
Figure 36
FORmEXLINEDESCRIPTION4HE
mEXLINEISRATEDFORBOTHNATURALANDPROPANE
gas. A manual shut off valve is also provided
WITHTHEmEXLINE
The gas control valve is located on the right
side of the unit.
7HENUSINGSOLIDGASLINECONNECTORACCESS
THEVALVEBYREMOVINGTHEFRONTDOORASSEMBLY
on the valve access side and the access plate
see Figure 37)
.
4HEELECTRONICCONTROLVALVEHASAMM
NPT thread gas supply inlet.
"RINGTHESHUTOFFVALVEONTHEENDOFTHEmEXLINE
over to the hard pipe and tighten with wrenches
FROMABOVETHROUGHTHElREBOXOPENING
Secure all joints tightly using appropriate
tools and sealing compounds (ensure propane
resistant compounds are used in propane ap-
plications). It is recommended to seal around
the gas line to prevent cold air leakage.
Figure 38
Gas Valve
Access Plate
Right Side
Modesty Panel
Figure 37
NOTE: The gas supply line must
be installed in accordance
with building codes by a quali-
fied installer approved and/or
licensed as required by the
locality. In the Commonwealth
of Massachusetts, installation
must be performed by a licensed
plumber or gas fitter.
Gas
Valve
3/8" NPT x
Flare Fitting
3/8" Flex Tubing
3/8" Nipple
3/8" Union
3/8" Close
Nipple
3/8" Shut-off Valve
1/2" x 3/8"
Reducer
Gas
Stub
1/2" x 3/8" Flare
Shut-off Valve
Gas Solid Line Connector
Gas Flex Line Connector
*Sediment
Trap
3"
Min
Figure 36—Gas Connection
A.
,IGHT THE APPLIANCE REFER TO THE LIGHTING
INSTRUCTIONSLABELINTHECONTROLCOMPARTMENT
or in the Care and Operation Instructions
MANUAL
B.
"RUSHALLJOINTSANDCONNECTIONSWITHTHEGAS
LEAKTESTSOLUTIONTOCHECKFORLEAKS)FBUBBLES
are formed, or gas odor is detected, turn the
RECEIVERORREMOTECONTROLTOTHEh/&&vPOSITION
%ITHERTIGHTENORREFASTENTHELEAKINGCONNECTION
THENRETESTASDESCRIBEDABOVE
C.
7HENTHEGASLINESARETESTEDANDLEAKFREE
BESURETORINSEOFFTHELEAKTESTINGSOLUTION
D.
2EINSTALLTHEACCESSPLATEMAKINGCERTAINTHE
GASKETHASNOTBEENDAMAGED
Step 7. CHECKING APPLIANCE
OPERATION
4URN ON BURNER THEN OBSERVE THE INDIVIDUAL
TONGUESOFmAMEONTHEBURNER-AKESUREALL
ports are open and producing flame evenly
ACROSSTHEBURNER)FANYPORTSAREBLOCKEDOR
PARTIALLYBLOCKEDCLEANOUTTHEPORTS
7ITHGASLINEINSTALLEDRUNINITIALSYSTEMCHECK
-
OUTBEFORECLOSINGUPTHEFRONTOFTHEUNIT&OLLOW
the lighting instructions provided in the Care
and Operation Instructions manual.
NOTE:
Lighting Instructions are also found on
the literature tag tied to the bracket above the
gas valve. To access the tag, reach into the
right side opening.
7HENlRSTLIGHTINGTHEAPPLIANCEITWILLTAKEAFEW
minutes for the line to purge itself of air. Once
PURGINGISCOMPLETETHEPILOTANDBURNERWILL
light and operate as indicated in the instruction
MANUAL3UBSEQUENTLIGHTINGOFTHEAPPLIANCEWILL
NOTREQUIRESUCHPURGING)NSPECTTHEPILOTmAME
REMOVELOGSIFNECESSARYHANDLINGCAREFULLY
Electronic Appliance Checkout
4OLIGHTTHEBURNERTURNh/.vTHEOPTIONALREMOTE
wall switch or turn the appliance mounted ON/
/&&SWITCHTOTHEh/.vPOSITION%NSURETHE
igniter lights the pilot. The pilot flame should
engulf the flame sensor as shown in
Figure 38
.
TEST ALL CONNECTIONS FOR GAS LEAKS
(FACTORY AND FIELD):
Pilot
Hood
Flame Rod
(Sensor)
Igniter
