28
./4%$)!'2!-3),,5342!4)/.3!2%./44/3#!,%
)../6!4)6%(%!24(02/$5#43s$)2%#46%.4'!3&)2%0,!#%3-ONTEBELLO$,8-ONTEBELLO$,8#$ s).34!,,!4)/.).3425#4)/.3
Figure 53
Figure 52
Glass Door
Assembly
Fireplace
Finish Combustible
Or Non-Combustible
Material
Bottom Of
Fireplace
1/8”
Minimum
Door Track
Finish Combustible
Or Non-Combustible
Material
Front Face
Of Fireplace
Floor Panel
.ONCOMBUSTIBLEMATERIALSSUCHASSURROUNDSANDOTHERAPPLIANCETRIM
MAYBEINSTALLEDONTHEAPPLIANCEFRONTFACEWITHTHEEXCEPTIONS
6ERTICALINSTALLATIONCLEARANCESTOCOMBUSTIBLEMANTELSVARYACCORDING
TOTHEDEPTHOFTHEMANTELSEE
Figure 8
)
-ANTELSCONSTRUCTEDOFNON
COMBUSTIBLEMATERIALSMAYBEINSTALLEDATANYHEIGHTABOVETHEAPPLIANCE
opening.
#OMBUSTIBLEMATERIALSMAYPROJECTBEYONDTHESIDEOFTHElREPLACEOPEN
-
INGASLONGASITISKEPTWITHINTHESHADEDAREAILLUSTRATEDIN
Figure 9
.
* Insulation is NOT ALLOWED in the clearance zones around vent
components. Keep this area free from combustible materials.
2 Foot Vertical
Vent & 90° Elbow
3" Min.
(76 mm)*
Top of
Appliance
8-3/8" Min.
(213 mm)
Combustible
materials are
allowed above
this point on
the face of the
appliance.
The gray shaded
area must be
non-combustible
or Dura Rock
Header
(2x4’s)
Spacers
Top of Door Frame
Fireplace (right side)
Combustible
Finished Wall
Materials
1
*
Installations with horizontal terminations which have minimum
vertical vent height only will require 4”(102mm) minimum
side clearance as shown in shaded zone above. All other
installations require 1" (25mm) minimum side clearance as
specified in
Figure 4 on Page 6
.
1
Figure 51
FINISHING REQUIREMENTS
Wall Details
#OMPLETElNISHEDINTERIORWALL4OINSTALLTHEAPPLIANCEFACINGmUSHWITH
THElNISHEDWALLPOSITIONFRAMEWORKTOACCOMMODATETHETHICKNESSOF
THElNISHEDWALL
(
Figure 51
).
!HEARTHEXTENSIONISNOTREQUIREDWITHTHISAPPLIANCE)FAHEARTHEXTENSION
ISUSEDTHEREARETWOMETHODSOFINSTALLATION/NETHElNISHCOMBUSTIBLE
ORNONCOMBUSTIBLEMATERIALCOULDBEENDEDBYBUTTINGUPAGAINSTTHE
FRONTFACEOFTHElREPLACEANDTHEmOORPANEL
refer to
Figure 52
)
.
4WOTHElNISHCOMBUSTIBLEORNONCOMBUSTIBLEMATERIALCOULDBEENDED
BELOWTHElREPLACE
(refer to
Figure 53
)
. Remove the floor panel as shown
in
Figure 52
BYREMOVINGTHESCREWSONTHERIGHTSIDEOFTHEPANELAND
SLIDINGTHELEFTSIDEAWAYFROMTHETAB$ISCARDTHESCREWSANDmOORPANEL
It is critical that there is at least a 1/8" gap between the bottom of the
door track and the surface of the finish material.
