manualshive.com logo in svg

Astria Fireplaces Aries Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Astria Fireplaces Aries Series Скачать руководство пользователя страница 59

Operation 

900004-01, 03/2017

Innovative Hearth Products
Aries™ Direct-Vent Gas Fireplaces

59

Glass Media

Removing and cleaning the glass media

 CAUTION 

Risk of personal injury. Allow the media to completely cool before handling.

Use a clean, dry, empty shop vac to remove glass media. Wash the media in warm, soapy water. Rinse and dry 
before reinstalling.

Reinstalling the glass media

Carefully follow the placement instructions 

(

Page 51

)

. This will ensure a proper fl ame and safe combustion.

NOTE: 

Improper positioning of media can create carbon build-up and will alter the performance of the fi replace.

Replacing the media

If the media needs replacement, use only the proper replacement media from manufacturer 

(

Page 70

)

.

Cleaning the burner

Carefully remove the logs/media. Vacuum out any foreign matter on the burner (e.g., lint, carbon, etc.). Ensure the 
burner ports are free of debris.

NOTE: 

Improper positioning of logs/media can create carbon build-up and will alter the performance of the fi replace.

Inspecting the wiring

Refer to the wiring diagram 

(

Figure 32

)

.

 CAUTION 

When servicing controls, label all wires prior to disconnection. Wiring errors can cause 
improper and dangerous operation. Verify proper operation after servicing.

 ATTENTION 

Au moment de l’entretien des commandes, étiquetez tous les fi ls avant de les débrancher. 
Des erreurs de cáblage peuvent entraîner un fonctionnement inadéquat et dangereux.

Inspect and clean all wire connections. Ensure that there is no wire melting or damage. The inspection should 
include:

• 

Terminals at the valve

• ON/OFF 

switch

• 

Optional wall thermostat, remote control, or wall switch

Содержание Aries Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды