manualshive.com logo in svg

Astria Fireplaces Aries Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Astria Fireplaces Aries Series Скачать руководство пользователя страница 20

Installation 

900004-01, 03/2017

Innovative Hearth Products
Aries™ Direct-Vent Fireplaces

20

If you require a rear vent unit, check to see if rear venting has a vent cap and insulation in place. If so, remove cap and any insulation 
in vent pipes, make sure fl ue is open completely to fi rebox inside. Once fl ue pipe has clear passages on inner and outer pipes, proceed 
with vent connections.

Preparing 45” Fireplaces for Top Venting Confi guration

If you require a top vented unit, follow the next steps to convert before use.

Step 1.

 Remove the 8 screws 

holding top vent cover plate and 
gasket. Retain screws.

Step 2.

 Remove the round fl ue 

cover from top venting outlet 
and all insulation from inside 
fl ue inner and outer pipe.

Step 3. 

Remove all insulation 

from inside fl ue inner and outer 
pipe. Retain insulation.

Step 4.

 If rear vent does not 

have a cap already installed, 
pack inner and outer pipe with 
the insulation from top.

Step 5.

 Remove and discard 

the large round gasket attached 
to the back of the unit. Install 
the cap from the top onto the 
rear pipe by bending tabs out 
securing with screws to rear 
outer wrapper.

Step 6.

 Reinstall screws to seal 

holes in wrapper.

Step 7.

 Remove the rear 

vertical Baffl e from top, retain 
screws but discard baffl e. 
Reinstall screws to seal holes 
after vertical baffl e is removed. 
Discard the vertical baffl e.

Step 8.

 Remove the 2 screws 

holding the block off plate and 
gasket to top vent fl ue. Retain 
screws as they will be re-used.

Step 9. 

Remove the 4 screws 

around the rear vent and use 
to Re-install block off plate and 
gasket over the rear vent fl ue.

Step 10. 

Using the 2 screws 

from the rear vertical baffl e, 
Install the top baffl e (shipped in 
bottom of unit) see photo.

Step 11.

 Ensure fl ue passage 

is clear to inside of fi rebox, 
and that outer pipe is free of 
insulation.

Unit is now ready to install 
as top-venting fi replace.

VENT SYSTEM PREPARATION

7. 

 Select a Horizontal or Vertical Vent System

1. 

With the fi replace secured in the framing, determine the vent route and identify the exterior termination location. 
The following sections describe vertical (roof) and horizontal (exterior wall) vent applications. Use only approved 
vent components 

(

Pages 45

 and 

46

)

.

NOTE: 

This fi replace must be vented directly to the outside.

 WARNING 

The vent system may not service multiple appliances, and must never be connected to a 
fl ue serving a separate solid fuel burning appliance.

NOTE: 

The vent pipe is tested to be run inside an enclosed wall (such as a chase). There is no 

requirement for inspection openings in the enclosing wall at any of the joints in the vent pipe.

Содержание Aries Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды