manualshive.com logo in svg

Astria Fireplaces Aries Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Astria Fireplaces Aries Series Скачать руководство пользователя страница 1

 -  Do not store or use gasoline or other fl ammable 

vapors and liquids in the vicinity of this or any 
other appliance.

 -  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance. 
•  Do not touch any electrical switch; do not use 

any phone in your building. 

•  Leave the building immediately.
•  Immediately call your gas supplier from a neigh-

bor’s phone.  Follow the gas supplier’s instruc-
tions. 

•  If you cannot reach your gas supplier, call the 

fi re department.

 -  Installation and service must be performed by 

a qualifi ed installer, service agency or the gas 
supplier.

       

WARNING:

FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could 
result in serious injury, death, or property damage.

        AVERTISSEMENT:

RISQUED’INDENDIE OU D’EXPLOSION
Le non-respect Des avertissements de sécurité 
pourrait d’entraîner des blessures graves, la mort 
ou des dommages matériels.

 -   Ne pas entreposer ni utilizer d’essence ni d’autres 

vapeurs ou liquides infl ammables dans le voisinage 
de cet appareil ou de tout autre appareil.

 -   QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.
• Ne touchez à aucan interrupteur. Ne pas vous servir 

des téléphones se trouvant dans le bâtiment où 
vous trouvez. 

•  Sortez immédiatement de bâtiment.
• Appelez immédiatement votre fournisseur de 

gaz depuis un voisin. Suivez les instructions du 
fournisseur. 

• Si vous ne pouvez rejoindre le fournisseur de gaz, 

appelez le service des incindies.

  -    L’installation et l’entretien doivent être assurés par 

un installateur ou un service d’entretien qualifi é 
ou par le fournisseur de gaz.

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future 
reference.

Installateur : Laissez cette notice avec l’appareil.
Consommateur : Conservez cette notice pour 
consultation ultérieure.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) 
or mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas 
indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certifi ed kit 
is used.

Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements 
locaux le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque 
signalétique.  Cet appareil ne peut être converti à d’autres gaz, sauf si une trousse de conversion est utilsée.

Installation and Operation Instructions

Models

C

US

Report No. F13-094

Ce manuel est disponible en francais, simplement en 
faire la demande. Numéro de la pièce 900004-03.

P/N 900004-01   REV. J   03/2017

Aries™ Series Direct-Vent Fireplaces

Aries33TMN
Aries33TMP

Aries33TEN
Aries33TEP

AriesCD33TMN
AriesCD33TMP

AriesCD33TEN
AriesCD33TEP

AriesCD33RMN
AriesCD33RMP

AriesCD33REN
AriesCD33REP

AriesCD35TMN
AriesCD35TMP

AriesCD35TEN
AriesCD35TEP

Aries33RMN
Aries33RMP

Aries33REN
Aries33REP

Aries35TMN
Aries35TMP

Aries35TEN
Aries35TEP

Aries35RMN
Aries35RMP

Aries35REN
Aries35REP

AriesCD35RMN
AriesCD35RMP

AriesCD35REN
AriesCD35REP

Aries40TMN
Aries40TMP

Aries40TEN
Aries40TEP

AriesCD40TMN
AriesCD40TMP

AriesCD40TEN
AriesCD40TEP

Aries40RMN
Aries40RMP

Aries40REN
Aries40REP

AriesCD40RMN
AriesCD40RMP

AriesCD40REN
AriesCD40REP

Aries45DMN
Aries45DMP

Aries45DEN
Aries45DEP

AriesCD45DMN
AriesCD45DMP

AriesCD45DEN
AriesCD45DEP

Traditional

Contemporary

P900004-01

Содержание Aries Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды