background image

Inst315 

– Viron e-Quilibirum Series Chlorinator Instructions V07_14 

10 

ii. 

INSTALL

 allows the unit to be set up for your pool or spa.  This should only be selected in the initial start 

up of your Chlorinator.    Select INSTALL and the following will occur: 

a. 

TIMER ENABLED

 

– this function will turn your timer on or off.  If the chlorinator is not connected to an 

external timer clock or Genus Remote Control system Press 

ACCEPT

.   If an external timeclock is used to 

operate the chlorinator and filter pump then change to disabled. 

b. 

FAST COMMS 

– set standard to YES, this option will only need to be changed if using a older version 

Hurlcon controller (no touchscreen) 

c. 

VARIABLE SPEED PUMP

 

– select YES if you have an AstralPool 3 speed pump. This will allow you to 

program the speed of the pump as part of the timer setting in the chlorinator. 

d. 

FLUSH AFTER TIMER 

– select YES and your pump will come on momentarily after the timers have 

finished to flush any residual chemicals from the mixing cell. 

e. 

PUMP FLOW CHECK 

– If active this function will monitor the flow sensor inside the chlorinator cell. If the 

presence of water flow is not detected for over 5 minutes, power to the pump outlet will be shut down to 
prevent your pump running dry. 

f. 

ENABLE LIGHT

 

– Your SM series chlorinator has an output to operate a single AstralPool ARC LED light.  

g. 

CELL REVERSAL PERIOD

 

– Standard setting is 4 hours. This should not be changed without consulting 

with your local AstralPool dealer or service department. 

h. 

REVERSE CELL? 

– This feature can be used to perform a manual reverse of your chlorinator cell – 

designed for use by your pool technician only. 

i. 

SET POOL WATER VOLUME

, select 

YES

 and then use up or down arrows to change the volume of your 

pool.  Press 

ACCEPT

 

j. 

SET SPA WATER VOLUME

, select 

YES 

if your have a SPA attached to your pool and then set volume.  

Press 

ACCEPT

 

k.  RESET SYSTEM?

 

– 

SELECT NO 

(This option will revert your chlorinator back to factory settings. It 

should only be used if your SM series chlorinator enters an error that cannot be cleared)

 

 

Cycle through 

POOL MODE

 button to select

 Auto

Manually ON

 or 

Manually OFF

AUTO

 will allow the unit to operate your filter pump, chlorine production and pH adjustment on the timer 

periods you have selected.  If you have not changed the timer periods, the default timer turns the filter pump 
and unit on at 08:00 hours for a period of 4 hours and then again at 16:00 hours for a further period of 4 hours.  
This is the default setting from the factory. 

 

Содержание Viron eQuilibrium Salt Chlorinator





























Отзывы: