Inst.419 Astral Pool Connect LITE+ Instructions V08-20
6
Press
“EQUIPMENT”
and the Connect LITE+ controller will start to detect other AstralPool devices that
are connected to the Connect LITE+
The list of “FOUND” equipment will be displayed for a few seconds and then the installation can continue.
“TIMERS ENABLED”
is the default setup (unless a Touchscreen has been detected). If you do not wish
to use timers (Auto Mode) then you can use the arrow buttons to change it to Timers Disabled. Press
ACCEPT to store this setting
“USE 3 SPEED PUMP?”
Use the arrow keys to select Yes if an Astral Pool 3 speed pump is being used
otherwise select No. Press ACCEPT to store this setting.
“ALLOCATE CHANNEL 1”
If a Viron or EQ Chlorinator was detected, Channel 1 will default to FILTER
PUMP otherwise it will default to UNUSED. N.B. You can use the arrow keys to select FILTER PUMP if a
Viron or EQ Chlorinator is being added after the Connect LITE+ installation. Press ACCEPT to store this
setting
“ALLOCATE POWER” “CHANNEL 2 OUTLET”
Use the arrow keys to allocate the Name of the
equipment that is plugged into the Channel 2 power outlet and then press ACCEPT N.B. If there is no
equipment plugged into this power outlet it can be allocated to UNUSED and then it won’t appear in other
menus.
“ALLOCATE POWER” “CHANNEL 3 OUTLET”
Use the arrow keys to allocate the Name of the
equipment that is plugged into the Channel 3 power outlet and then press ACCEPT N.B. If there is no
equipment plugged into this power outlet it can be allocated to UNUSED and then it won’t appear in other
menus.
“ALLOCATE NAME” “ALLOCATE ZONE 1 NAME”
Use the arrow keys to allocate the Name of Lighting
Zone 1 and then press ACCEPT
“ALLOCATE NAME” “ALLOCATE ZONE 2 NAME”
Use the arrow keys to allocate the Name of Lighting
Zone 2 and then press ACCEPT. N.B. If only one Zone of Lighting is required, then Lighting Zone 2 Name
should be set to NONE and then it won’t appear in other menus.
“ALLOCATE LIGHTS” “LIGHT OUTLET A”
Use the arrow keys to allocate the Light that is plugged into
Light Outlet A to a Lighting Zone
Repeat the above step to allocate the Lights plugged into LIGHT OUTLET B, C & D.
Refer to Section 4.1 Advanced Installation Instructions for
“ADVANCED SETUP”
3.0 Using your Controller
The Display on the Connect LITE+ will go into “sleep mode” after 1 minute of inaction and the display will turn
dark.
To return from “sleep mode” press any button on the control panel. (This initial press will not cause any action
other than to turn the display back on)
Your Connect LITE+ Controller operation can be divided into 5 areas;
a.
“MAINT” - Maintenance selects specialised functions of your controller and initial set up to suit your pool.
b.
“CONTROL” - Allows you to manually control individual “POWER” Outlets or “LIGHTS” and set them to ON,
OFF or AUTO modes.
c.
CLOCK Button - Allows you to set the current time.
d.
TIMER Button - Allows you to set timers to control the Power and Light outputs.
e.
MODE Button - Allows you to set all of the Power and Light outputs to All On, All Off or All Auto.
3.1 Setting Timers on your Connect LITE+ Controller.
Your Connect LITE+ has 4 timers per day enabling you to set different periods in which your
Chlorinator/Filtration pump, Lights and other items of equipment can be run. Timers are set by entering a
start time, and a RUN time for how long you want equipment to operate.
Within a Timer period, you can either set Equipment and Lights to be in either AUTO mode or OFF mode.
To set the Timers use the following sequence:
Press the TIMER button.
