background image

Warranty 

PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY 

BEFORE USING YOUR ASTON GLOBAL BATHROOM PRODUCT. BY USING THE 

PRODUCT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING 

WARRANTY TERMS AND CONDITIONS. 

SHOWER DOOR/SHOWER TRAY 

Aston Global Inc. Parts-Only Limited Warranty 5 years 

Warranty for any part in oil rubbed bronze finish is limited to two (2) years. 

Aston Global,  Inc.  ("Aston Global") warrants to the original retail purchaser  ("Owner") of 

any Shower Door/Tray product ("Product"), at the original installation site, for a period of 

Five (5) years from date of purchase (whether directly from Aston Global or an authorized 

reseller) that the Product manufactured by Aston Global is free from manufacturing 

defects in materials and workmanship, when used under normal conditions and when 

such Product has not been modified or changed in any manner after leaving Aston 

Global's warehouse or plant.  If any Product manufactured by Aston Global is found to 

have manufacturing defects in materials or workmanship, such Product will be repaired or 

replaced by Aston Global. This warranty applies only against defects discovered within 

the warranty period and extends only to the original purchaser of the Product.  Parts 

repaired or replaced under the terms of this Warranty will be warranted for the remainder 

of the original warranty period only. 

Proof of purchase is required to exercise this Warranty.  Aston Global may, at its option, 

examine and inspect the alleged defective Product, and Aston Global may request that 

parts be returned to Aston Global at Owner's expense for factory inspection. The 

determination as to whether Product shall be replaced, or in the alternative, repaired, shall 

be made solely by Aston Global.  If a Product is determined to be covered by the above 

Warranty, Aston Global will ship the replacement part(s) to Customer by either ground 

shipping or US postal service.  Increased costs for expedited delivery, if requested by 

Customer, are the responsibility of Customer.  Parts not currently in stock may require up 

to a 6 week delivery time after placement of order. 

The above warranty is subject to the following conditions:  (1) the Product must be 

installed in a single family dwelling unit where the original purchaser of the Product 

resides; and (2) the Product must be maintained as described in the owner's 

manual supplied with the Product. 

For glass and acrylic panels, the customer must (a) open and inspect the Product 

upon delivery (without releasing the delivery driver until visual verification that the 

Product arrived in a good and acceptable condition); and (b) clearly notate damage 

on the delivery acknowledgment receipt.  Failure to do so, and any damage 

discovered to glass or acrylic panel after delivery, will be repaired or replaced at 

the sole discretion of Aston Global. 

21 

Содержание Langham SDR978




























Отзывы: