background image

2.  Using the appropriate drill bit for your wall surface drill the hole locations with a 

5/16" diameter drill bit.  Install the plastic anchors provided into the drilled 

holes.  Repeat for the other side.  See figure 2 

3.  Attach wall mounts (6) to wall using  M5 x 40 screws from Screw Pack 1. 

Repeat the installation of wall mounts for other side.  See figure 3. 

4.  Position glass clamp (7) on shower tray and attach to shower tray using M4 x 40 

screws from  screw pack 1. The glass clamp should be positioned so the single 

hole is facing toward the inside of shower.  See figure 6. 

5.  Slide rail ends (5) onto top rail (2) and loosely tighten into place.  Note:  The set 

screws in rail end are not centered, and one of rail end is threaded.  The rail 

ends (5) should be installed on top rail (2) so that threaded end of rail end (5) is 

facing outward.  See figure 4. 

ATTENTION:  A 

minimum of two people are required for the next assembly steps. 

6.  Position the top rail/fixed glass assembly into your shower opening.  Loosen set 

screws in rail end (5).  Next screw rail end (5) onto wall mount (6) and tighten. 

Repeat on other side.  See figure 5. 

7.  Install the glass clamp (6) to fixed glass (3) using hardware provided.  See 

figure 6 for details.  Flat smooth surface of glass clamp (6) should be installed 

on outside of fixed glass (3). 

8.  Insure plastic sliding door glide is in place in underside of sliding door track 

divider (8) and positioned to proper location for 10mm glass thickness.  See 

figure 7. 

9.  Position the sliding door track divider (8) into position as seen in figure 8 and 

mark the 2 shower base hole positions. 

Note:  In drawing 8 the hole 

locations for attaching sliding door track divider should be  1 13/16" 

from edge of fixed glass.  See details in figure 8. 

NOTE:  If your surface is prone to cracking or chipping then it is 

recommended that you pilot drill first using a smaller drill bit, and then step 

up to the final size. 

10.  Using the appropriate drill bit for your tray surface drill hole locations with 1/8" 

diameter drill bit.  Position the sliding door track divider (8) over drilled holes on 

shower tray, and secure sliding door track divider (8) to shower tray using 

hardware in screw pack 2.  See figure 9. 

12 

Содержание Langham SDR978




























Отзывы: