Assum DZ SERIES Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 33

Assum DZ SERIES Скачать руководство пользователя страница 11

9

2.Safety

1). Ready to use:

This specification describes in detail the product handling, storage, installation,

startup, operation conditions, maintenance, troubleshooting and maintenance and
installation of the machine, it is recommended by a trained professional.

Make sure to follow the maintenance instructions
Before using the machine, make sure to read this manual and fully understand.
If you have any questions, please contact the manufacturer or supplier.

2). Safety precautions:

Make sure the machine using the power supply voltage, frequency, avoid errors. No
matter three phase four-wire (AC380v/50Hz) or single-phase (AC220v/50Hz)power
supply, yellow and green wire to ground protection, cannot be removed.
Avoid power cord compression, pull, roll power cord when it is not used.
Do not use in corrosive, big powder place.
Do not arbitrarily replace parts on the machine.
Please keep the machine clean inside and outside, as well as the removal of the
vacuum chamber adhesive material.
When the machine is not in use should be cut off the power.
Please change the vacuum pump oil in time.
Save them for future reference.

The product according to the latest technical and safety standards for manufacturing, if
used improperly, may be dangerous or damage, safety precautions Keywords "Danger",
"Warning", "Caution" notes.

Model

DZ-500/2E L:1040MM

Voltage

AC 220V/50Hz 110V/60Hz

Motor Power

2000W

Sealing Power

750W

Ultimate Vacuum Pressure

1KPa

No. of Sealing Bars for Each Chamber

2pcs

Chamber Dimension(L

×

W

×

H)

1000X520X170mm

Sealing Length

500mm

Sealing Width

10mm

Vacuum Pump Rate

40m

3

/h

Material for Vacuum Chamber

Stainless steel

External Dimension (L

×

W

×

H)

1040x575x980mm

Net Weight

230kgs

Distance of Two Sealing Bars

900mm

«
...
9
10
11
12
13
...
»

Содержание DZ SERIES


































Отзывы:

Нет отзывов