Assa Abloy SARGENT Profile Series страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 28

6 1-800-810-WIRE • www.sargentlock.com •

A7765C

Copyright © 2018, Sargent Manufacturing Company

, an ASSA ABLOY Group company

. All rights reser

ved.

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

01/31/18

Profile Series v.S1 PoE Exit Device

PoE Door Harness

Order of installation may vary.
Refer to appropriate sections for instructions.
1.  Prop door open.
2.  Tape the two lock-side 4-pin connectors to the ring terminal.
3.  Using the ring terminal, carefully fish the assembly through the door channel to the lock.
4.  Remove tape from ring terminal and door harness connectors.

Hinge-side harness connectors:

• 4-pin male Molex connector
• 6-pin male Molex connector with ground wire

Lock-side harness connectors:

• Ring terminal
• (2) 4-pin connectors

C

Installation Wiring (Continued)

Ground

4-Pin

4-Pin

6-pin M

Cable

: CAT 5e,

26 AWG stranded,

shielded, 100ohm

Ring Terminal Secured

to Lock Mounting Plate

4-pin F

Drain Wire

PoE Lock

«
...
4
5
6
7
8
...
»

Содержание SARGENT Profile Series





























Отзывы:

Нет отзывов

Похожие инструкции для SARGENT Profile Series

Бренд: danalock Страницы: 24

Бренд: Olivari Страницы: 2

Бренд: Waferlock Страницы: 21

Бренд: Chamberlain Страницы: 2

Yale Smart Latch

Бренд: Assa Abloy Страницы: 2

Бренд: Satel Страницы: 4

Бренд: Fenner Drives Страницы: 16

Showerite Owner’s

Бренд: American Standard Страницы: 6

Бренд: KEYA Страницы: 14

Бренд: Turbolock Страницы: 36

1Touch evo3 Series

Бренд: Intelligent Biometric Controls Страницы: 14

Бренд: FA Parkes Страницы: 2

Бренд: Turbolock Страницы: 35

Бренд: Yale Страницы: 2

Бренд: Command access Страницы: 2

Assa Abloy IN120

Бренд: Sargent Страницы: 20

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды