Assa Abloy Corbin Russwin ED5400 (A) Series Скачать руководство пользователя страница 7

Страница: 7 / 16

Surface Vertical Rod

Installation Instructions

Exit Devices

FM164 09/19

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • [email protected]

Preparation (cont .)

Mark Door

Locate and mark horizontal and

vertical centerlines as shown . (Figure 9)

LHR door shown. Preparation is typical for both

door hands.

Caution

If device is mounted higher or lower than

shown, rod length must change. Lengthen or

cut top and bottom rods as shown in Step 3c.

LBR

For ED5470 Series Less Bottom Rod Devices,

skip bottom latch and strike

installation steps and see separate

instructions for ED5470 Series top latch

and strike.

Note

Less Bottom Rod Devices should not be used

where security is a primary concern.

Prepare Door, Frame, and Sill

A. Locate Device Template aligning VERTICAL REFERENCE and HORIZONTAL REFERENCE lines on door and

template. Tape template to door face.

(Figure 10)

B. Extend centerline of Rod and Strikes from Device Template to top and bottom of door.
C. Locate Top Latch/Strike, Bottom Case, and Bottom Strike

templates, aligned on centerline of Rods and Strikes on door.

Tape templates in place and mark holes.

D. Locate and tape Trim Template to door

(see instructions with Trim).

E. Mark and prepare holes per installation template:

•

Device and Bolt Case Plates:

Each: (2) 1/4-20 Machine Screws for metal reinforced doors

(2) 3/8" (10 mm) Dia. Sex Nuts & Bolts.

•

Top Strike:

ED5400 Series: (2) 10-24 Machine Screws,

(2) #10 Wood Screws.

ED5470 Series: (4) 10-24 Machine Screws.

•

Bottom Strike:

5/8

(16 mm) Dia. 3/4

(19 mm)

Deep hole.

Figure 9

Measure Gap

Write Dimension here: XXXX"

Door

2-3/4"

(70 mm)

39-15/16"

(1014 mm)

Horizontal reference

Vertical reference

Finished floor

Single

Door

or Pair

Without

Mullion

LHR Door

Inside Face

Figure 10

Bottom Strike

Template

Bottom Case

Template

Device

Template

Top Latch

& Strike

Template

LHR Door

Inside Frame

Vertical

Reference

Horizontal

Reference

Rods & Strikes

Finished floor

Содержание Corbin Russwin ED5400 (A) Series

















Результаты поиска

Содержание Corbin Russwin ED5400 (A) Series

Отзывы:

Похожие инструкции для Corbin Russwin ED5400 (A) Series

Бренды по названию

Популярные бренды

Assa Abloy Corbin Russwin ED5400 (A) Series, Руководство по установке

Результаты поиска

Содержание Corbin Russwin ED5400 (A) Series

Отзывы:

Похожие инструкции для Corbin Russwin ED5400 (A) Series

Бренды по названию

Популярные бренды