Assa Abloy Corbin Russwin ED5400 (A) Series Скачать руководство пользователя страница 11

Страница: 11 / 16

Surface Vertical Rod

Installation Instructions

Exit Devices

FM164 09/19

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • [email protected]

Installation (cont .)

Complete Installation

A. Install rods as shown. (Figure 19)
B. Set strike roller between tripping lever

and bolt. Adjust and shim strike

as needed.

C. Test device action by touchbar, by trim,

and by dogging. ADJUST AS NEEDED. Upper

bolt should retract 1/2" (12 mm).

Bolts extend when door shuts and top

strike hits tripping lever.

D.  Adjust bottom rod (tilt rod out and turn).
E.  Adjust top rod (tilt rod out and turn).
F.  After acceptable device

function, install third screw

in top stike to lock stike in position

(ED5400) 10-24 x 5/8" FHMS. Install

two (2) remaining screws in top to lock

strike (ED5470).

G. Install latch covers, rod guide covers, and

device cover.

See Figure 1 for fastener specifications.

MAINTENANCE:

1. Periodically remove covers and coat

mechanisms with a silicone base

lubricant. This is particularly required in

corrosive environments for proper

product function.

2. Check mounting fasteners periodically.

Retighten if found loose. Apply screw

locking compound (available at

automotive part stores) or change part

fasteners if screws continue to

back up.

3. Periodic checks (and adjustments) of

rods is required to compensate for

changes in the opening

(e.g. door sagging).

Figure 19

DO NOT PRELOAD BOLT

Cover Screw Hole

Strike

3/8

(10)

Shorter (CW)

Longer (CCW)

Top rod

Bottom rod

Concealed vertical rod

ED5200S

Содержание Corbin Russwin ED5400 (A) Series

















Результаты поиска

Содержание Corbin Russwin ED5400 (A) Series

Отзывы:

Бренды по названию

Популярные бренды

Assa Abloy Corbin Russwin ED5400 (A) Series, Руководство по установке

Результаты поиска

Содержание Corbin Russwin ED5400 (A) Series

Отзывы:

Бренды по названию

Популярные бренды