Assa Abloy Aperio AH15 Скачать руководство пользователя страница 41

Страница: 41 / 52

Aperio

Online Mechanical Installation Guide, Document No: ST-001323-B Date: 21 februari 2014

Aperio

Online

AH40 (Ethernet)

This chapter describes how to perform a default

configuration of an AH40 communication hub

using the Ethernet interface.

Configuration of the communication hub to

the EAC includes setting jumpers, connecting it

to Ethernet and connecting it to power supply,

according to applicable section below.

Setting jumper for internal/external antenna

Normally the communication hub’s internal

antenna is sufficient. In a difficult installation

environment or if the radio signal needs to be

amplified in a certain direction, an external

antenna can be used. Connect the two left

pins ("EXT") with the jumper to use an external

antenna.

Setting jumper for pariing mode

To activate automatic pairing, connect the two left

pins ("PAIR") with the jumper, see figure.

Connect to supply voltage

Connect the power and ground to the “+” and the

“-“ terminals of the connector marked “8V-24V”.

Note! Power supply input, 8-24 VDC, 3.5 W. The

power supply shall be a Limited Power Source

(LPS) according to EN 60950-1. The power

supply shall be 3 A over current protected. Wire

requirements 16-22 AWG.

Connecting Ethernet

Connect an Ethernet cable to the Hub and make

sure that the Ethernet “LINK” LED is green, which

indicates that the Ethernet link level is established.

The Hub supports 10/100 Mbit/s half and full

duplex with auto-negotiation.

Using Power over Ethernet (PoE)

The communication Hub can also be powered

using Power over Ethernet by connecting it to an

Ethernet switch or other equipment that supports

this.

Due to EMC regulations, do not connect

any other power supply when PoE is used.

Ethernet

Jumper for antenna

8-24V

- +

LINK

PAIR

ANTENNA

EXT INT

Jumper for pairing mode

Содержание Aperio AH15





















































Результаты поиска

Содержание Aperio AH15

Отзывы:

Похожие инструкции для Aperio AH15

Бренды по названию

Популярные бренды

Assa Abloy Aperio AH15, Инструкция по механической установке

Результаты поиска

Содержание Aperio AH15

Отзывы:

Похожие инструкции для Aperio AH15

Бренды по названию

Популярные бренды