Assa Abloy Adams Rite EX89 Скачать руководство пользователя

Страница: 1 / 10

Page | 1

800.872.3267

800.232.7329

[email protected]

www.adamsrite.com

EX89 Pullman Rim Exit Device

Preparation Guide and Installation Instructions

Box Contents

EX89 Pullman Rim Exit Device

Cylinder and Trim Interface Kit

Mounting Hardware Kit

Frame Kit with Templates

Mounting End Cap Kit

Recommended Installation Tools

Safety glasses

Measuring tape

Level

Pencil

Power drill

Drill bits: 5/32”, 3/4”

Center punch

Phillips screw driver

IMPORTANT NOTE 1: All work must be performed to applicable building, regulatory and life-
safety codes. Please consult local Authority Having Jurisdiction (AHJ) for more information.

IMPORTANT NOTE 2: The Americans with Disabilities Act (ADA) guidelines specify door
hardware be mounted 34”-48” above the finished floor.

Active Push Bar

Filler Plate

Back Bar

Содержание Adams Rite EX89











Результаты поиска

Содержание Adams Rite EX89

Отзывы:

Похожие инструкции для Adams Rite EX89

Бренды по названию

Популярные бренды

Assa Abloy Adams Rite EX89, Руководство по подготовке

Результаты поиска

Содержание Adams Rite EX89

Отзывы:

Похожие инструкции для Adams Rite EX89

Бренды по названию

Популярные бренды