Aspes AAS2009 Скачать руководство пользователя страница 7

Страница: 7 / 36

2. Parts Name and Function

Because there are many models, features and appearance will vary, we only introduce the follow pattern,

others please refer to using.

Indoor unit

Outdoor unit

Unit operation section

Operational performance/indications

Air return grid

Takes in the indoor air

Left/right air flow

direction

Up/down air flow direction

adjusting flap

Air outlet

Air filter

at sides & rear
surface

(Optional)

Drain tube

Air discharge vent

Refrigerant piping

connection, Eletric

wiring cord

Emergency operation key

How to close

How to open

Air blows out from here

Removes dust or dirt out of the inlet air

Drain the water dehumidified out of the air

Push down the air inlet grid and then push both sides

of air inlet grid at the bottom

Note: Do not open the grid at an angle over 60 degrees. Do not operate the units with too much force.

Indications of unit 1

Running indicator

WIFI(Optional)

Setting temperature, timer time,

and failure code indicator

ECO MODE

Electricheating(Optional)

Содержание AAS2009





































Результаты поиска

Содержание AAS2009

Отзывы:

Бренды по названию

Популярные бренды

Aspes AAS2009, Инструкция по эксплуатации

Результаты поиска

Содержание AAS2009

Отзывы:

Бренды по названию

Популярные бренды