Aspes AAS2009 Скачать руководство пользователя страница 5

Страница: 5 / 36

Safety

1. Safety Precautions

Read Safety Precautions Before Installation

Incorrect installation due to ignoring instructions can cause serious damage or injury.

The seriousness of potential damage or injuries is classiﬁed as either a WARNING or CAUTION.

This symbol indicates that ignoring instructions may cause death or serious injury

This symbol indicates that ignoring instructions may cause moderate injury to your

person, or damage to your appliance or other property.

Caution

arning

Ask an authorized dealer to install this air conditioner. Inappropriate installation may cause water leakage,

electric shock, or fire.

All repairs, maintenance and relocation of the unit must be performed by an authorized service technician.

Inappropricate repairs can lead to serious injury or product failure.

This appliance can be used by children aged from 8 years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not

play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

1. Installation Warnings

2. Warnings for product use

If an abnormal situation arises (like a burning smell), immediately turn off the unit and pull the power plug.

Call your dealer for instrucions to avoid electric shock, fire or injury.

Do not insert fingers, rods or other objects into the air inlet or outlet. This may cause injury, since the fan may be

rotating at high speeds.

Do not use ﬂammable sprays such as hair spray, lacquer or paint near the unit. This may cause ﬁre or combustion.

Do not operate the air conditioner in places near or around combustible gases. Emitted gas may collect around

the unit and cause explosion.

Do not operate the air conditioner in a wet room (e.g., bath room or laundry room). This can cause electrical

shock and cause the product to deteriorate.

Do not expose your body directly to cool air for a prolonged period of time.

3. Electrical Warnings

Only use the speciﬁed power cord. If the power cord is damaged, it must be replaced by the manufacturer or

certiﬁed service agent.

Keep power plug clean. Remove any dust or grime that accumulates on or around the plug. Dirty plugs can

cause fire or electric shock.

Do not pull power cord to unplug unit. Hold the plug ﬁrmly and pull it from the outlet. Pulling directly on the cord

can damage it, which can lead to ﬁre or electric shock.

Do not use an extension cord, manually extend the power cord, or connect other appliances to the same outlet

as the air conditioner. Poor electrical connections,poor insulation, and insufﬁcient voltage can cause fire.

4. Cleaning and Maintenance Warnings

Turn off the device and pull the plug before cleaning. Failure to do so can cause electrical shock.

Do not clean the air conditioner with excessive amounts of water.

Do not clean the air conditioner with combustible cleaning agents. Combustible cleaning agents can cause fire

or deformation.

Содержание AAS2009





































Результаты поиска

Содержание AAS2009

Отзывы:

Бренды по названию

Популярные бренды

Aspes AAS2009, Инструкция по эксплуатации

Результаты поиска

Содержание AAS2009

Отзывы:

Бренды по названию

Популярные бренды