Aspes AAS2009 Скачать руководство пользователя страница 34

Страница: 34 / 36

Noise is heard cracking sound. After a power

stoppage or after disconnecting the power

supply plug.

Operation can not be restarted even if the

power is recovered.

Remote control signals are not received.

This is caused by heat expansion or contraction of plastics.

The memory circuit of the microcomputer is cleared.

Operate the remote controller again to restart the operation.

Remote control signals may not be received when signal

receiver on the air conditioner body is exposed to direct

sunlight or strong lighting. In that case, interrupt the sunlight

or darken the lighting.

Moisture may from on the air outlet grilles.

Communication failure of indoor and outdoor unit

T1 sensor fault
T2 sensor fault

T2B sensor fault

Malfunction of outdoor unit

Testing fault of zero-crossing signal

EEPROM malfunction

Wind testing fault of PG electricamotor

Communication fault of wire controller

Room card is not connected

E1
E2
E3
E4

E7
E8
E9

If the unit is operated for a long period of time with the high

humidity, mositure may from on the air outlet grilles and

drip down.

9. Phenomenon Analysis and Treatment measures

Continue above table

9.4 Display with Fault

Definitions of malfunction

Contents appearing

Содержание AAS2009





































Результаты поиска

Содержание AAS2009

Отзывы:

Бренды по названию

Популярные бренды

Aspes AAS2009, Инструкция по эксплуатации

Результаты поиска

Содержание AAS2009

Отзывы:

Бренды по названию

Популярные бренды