background image

 

       American Stainless Pumps, Inc. 

www.aspumps.com 

8

SSPC Exploded View 

Limited Warranty

American Stainless Pumps (ASP) warrants that its manufactured products are made of first class materials and in a skillful 
and workmanlike manner, and when properly installed and maintained, will operate as proposed in the company’s written 
documents. This warranty is in effect for a period of two years from shipment. 

 

 

ASP does not warranty against corrosion or erosion or wear of its products when placed in service.

 

 

 

ASP will pass through to its customers any warranties granted by the manufacturers of products purchased by ASP 
and sold with its manufactured products (such as motors or mechanical seals), but does not itself warrant these items.

 

 

 

Under no circumstances will ASP be liable for any penalties or any incidental or consequential damages caused by 
the failure of its products, by late delivery or by any other causes.

 

 

 

All  ASP  products  are  sold  FOB  The  Factory.  Freight  charges  for  returning  and  reshipping  products  are  the  buyer’s 
responsibility, regardless of warranty status.

 

 

 

There are no other warranties, expressed or implied, except for the warranties given here. This warranty may not be 
modified verbally by any employee or agent of ASP. 

Returns

All products returned to ASP for warranty evaluation must be authorized in advance by the issuance of a Return Material 
Authorization  number  (RMA#)  by  ASP.  The  returned  equipment  must  be  clearly  tagged  with  the  RMA#,  as  well  as  the 
name and address of the consignor. Any products proven to ASP’s satisfaction to be defective will be replaced or repaired 
at the ASP’s option. ASP will not pay for any transportation charges to or from its facilities. 

Shipments

All sales are FOB the ASP’s facility in Los Angeles CA. Acceptance of material by common carrier constitutes a shipment 
and ASP is not liable for any loss caused by the carrier. Customer is responsible for filing a claim against the carrier for 
equipment  damaged  or  lost  in  transit.  Claims  for  shortage  must  be  made  within  ten  (10)  working  days  of  receipt  of 
equipment or goods. 

Содержание SSP









Отзывы: