ASM Zip-Spray 1700 Скачать руководство пользователя страница 37

Страница: 37 / 38

309421

Technical Data

Working pressure range

0–3000 psi (0–21 MPa, 0–207 bar)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electric motor

5.8A (permanent magnet DC)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating horsepower

3/4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum delivery (with tip)

0.31 gpm (1.17 lpm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Paint hose

50 ft (15.2 m) x 1/4 in.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum tip hole size

0.017 in. (0.43 mm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Weight, sprayer only

31 lb (14 kg)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Weight, sprayer, hose, gun

36 lb (17 kg)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Dimensions
Length

19.5 in (49.5 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Width

17.25 in (43.8 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Height

40.75 in (103.5 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Height with folded handle

26 in (66.0 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power cord

16 AWG, 3 wire, 6 ft (1.8 m)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pump inlet fitting

3/4 in. internal thread (standard garden hose thread)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fluid outlet fitting

1/4 npsm external thread

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inlet screen on suction tube

35 mesh (450 micron)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wetted parts, pumps and hose

Stainless steel, brass, leather, ultra–high molecular weight

. . . . . . . . . . . . . . . . . . . . . .

polyethylene (UHMWPE), carbide, nylon, aluminum, PVC, polypropylene, fluroelastomer
Generator requirement

1500 Watt minimum

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electric power requirement

120V AC, 60 Hz, 1 phase, 15A

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage temperature range*†

–30

to 160

F (–35

to 71

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating temperature range**

to 115

F (4

to 46

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

When pump is stored with non–freezing fluid. Pump damage will occur if water or latex paint freezes in pump.

†

Damage to plastic parts may result if impact occurs in low–temperature conditions.

Changes in paint viscosity at very low or very high temperatures can affect sprayer performance.

Содержание Zip-Spray 1700







































Результаты поиска

Содержание Zip-Spray 1700

Отзывы:

Похожие инструкции для Zip-Spray 1700

Бренды по названию

Популярные бренды

ASM Zip-Spray 1700, Операция, ремонт и запасные части.

Результаты поиска

Содержание Zip-Spray 1700

Отзывы:

Похожие инструкции для Zip-Spray 1700

Бренды по названию

Популярные бренды