ASM Zip-Spray 1700 Скачать руководство пользователя страница 32

Страница: 32 / 38

32 309421

Motor Diagnostics

Check for electrical continuity in the motor armature,
windings, and brush as follows:

Motor Diagnostics

reveal a damaged motor, or if

either of the motor brushes are shorter than 1/4 in.
(6.4 mm), or if the motor shaft cannot turn, replace the
motor using

Motor Kit

245063

(see

List of Kits

, page

31)

Setup

Unplug electrical cord, and relieve pressure.

Remove right enclosure, and disconnect motor
harness from control board.

Remove fan brace.

Remove the four cover screws and front cover.

Remove yoke and guide rods, and remove gear.

Armature Short Circuit Test (Spin Test)

Quickly turn motor fan by hand. If there are no electri-
cal shorts, fan coasts two or three revolutions before
stopping. If fan does not spin freely, armature is
shorted. Replace motor using

Motor Kit

245063

(see

List of Kits

, page 31)

Armature, Brushes, and Motor Wiring Open
Circuit Test (Continuity)

Connect red and black motor leads together with
test lead. Turn motor fan by hand at about two
revolutions per second.

If there is uneven resistance or no resistance,
replace motor using

Motor Kit

245063

(see

List of

Kits

, page 31)

Control Board

Diagnostics

Check for a damaged control board or pressure control
switch as follows:

Unplug electrical cord, and relieve pressure.

Remove the four cover screws and front cover.

Remove yoke and guide rods, and remove gear.

Remove pressure control harness from control
board.

Using fingernail or tip of small,

flat-blade screwdriver, press tab on right side
connector to release.

Attach to the control board a harness from a
pressure switch that you know is functioning
correctly.

NOTE:

Pressure control switch does not have to

be installed in pump.

Turn pressure control adjustment knob to
maximum pressure setting.

Plug electrical cord into 120V AC receptacle, and
turn Power switch (B) ON.

If motor runs, replace pressure switch.

If motor does not run, replace control board
and repeat test using

Control Board Kit

243228

(see

List of Kits

, page 31)

Содержание Zip-Spray 1700







































Результаты поиска

Содержание Zip-Spray 1700

Отзывы:

Похожие инструкции для Zip-Spray 1700

Бренды по названию

Популярные бренды

ASM Zip-Spray 1700, Операция, ремонт и запасные части.

Результаты поиска

Содержание Zip-Spray 1700

Отзывы:

Похожие инструкции для Zip-Spray 1700

Бренды по названию

Популярные бренды