ASL INTERCOM DAX200 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 28

ASL INTERCOM DAX200 Скачать руководство пользователя страница 2

DAX200/DAX400 – Installation Guide

Copyright © 2009 Application Solutions (Safety and Security) Ltd.

Application Solutions (Safety and Security) Ltd.

Unit 17 Cliffe Industrial Estate

Lewes - East Sussex

BN8 6JL - UK

Tel: +44(0)1273 405411

Fax: +44(0)1273 405415

www.asl-control.co.uk

All rights reserved.

Information contained in this document is believed to be accurate, however no representation or warranty is given and Application
Solutions (Safety and Security) Ltd. assumes no liability with respect to the accuracy of such information.

Issue: 02 complete, approved

Page 2 of 28

This equipment is designed and manufactured to conform to the following EC standards:

EMC

EN55103-1/E1, EN55103-2/E5, EN50121-4, EN50130-4, EN61000-6-3,
ENV50204

Safety EN60065

Failure to use the equipment in the manner described in the product literature will
invalidate the warranty.

A 'Declaration of Conformity' statement to the above standards, and a list of auxiliary
equipment used for compliance verification, is available on request.

This product must be disposed of in accordance with the WEEE directive.

Contents

1

Installation ................................................................................................................................................ 3

2

Connections ........................................................................................................................................... 14

3

DAX and DAU Positioning..................................................................................................................... 19

4

Product Specification ............................................................................................................................ 21

5

Mechanical Dimensions ........................................................................................................................ 23

6

Safety and Precautions ......................................................................................................................... 25

Additional User Documentation:

Intellevac system user documentation and additional reference information are available from the ASL
website: www.asl-control.co.uk

«
1
2
3
4
...
»

Содержание DAX200





























Отзывы:

Нет отзывов